Komatsu PC290LC-11 Operation & Maintenance Manual page 485

INDEX
Machine - Secure................................................3-240
Machine - Secure with tie down point................. 3-241
Machine - Secure without tie down point............ 3-242
Machine - Set at angle.......................................... 4-34
Machine - Start (Travel forward and reverse) / Stop....
.....................................................................3-183
Machine - Start after long-term storage.............. 3-258
Machine - Steer (Change the direction).............. 3-186
Machine - Stop....................................................3-185
Machine - Store long-term.................................... 6-29
Machine - Swing................................................. 3-188
Machine - Travel forward.................................... 3-184
Machine - Travel reverse.................................... 3-185
Machine - Unload................................................3-251
Machine equipment name.......................................3-2
Machine monitor - Operate................................... 3-11
Machine monitor - Operate when operator identifica-
tion function is available with skip..................3-82
Machine monitor - Operate when operator identifica-
tion function is available without skip.............3-84
Machine monitor - Operate when starting engine in
abnormal situation......................................... 3-15
Machine monitor - Operate when starting engine in
normal situation..............................................3-11
Machine monitor - Operate when starting engine
while engine shutdown secondary switch is ON...
.......................................................................3-12
Machine monitor - Operate when starting switch is
ON while operator ID input is set................... 3-13
Machine monitor - Operate when stopping engine in
normal situation............................................. 3-12
Machine monitor - Operate when trouble occurs while
operating machine......................................... 3-16
Machine monitor equipment name..........................3-6
Machine operations and controls........................ 3-139
Machine ready for installation of attachment........ 6-14
Machine settings................................................... 3-68
Magazine box......................................................3-105
Main use of machine...............................................1-8
Maintenance during long-term storage............... 3-258
Maintenance interval for hydraulic breaker........... 4-13
Maintenance of air conditioner..............................2-50
Maintenance procedure........................................ 4-15
Maintenance schedule.......................................... 4-12
Maintenance schedule table................................. 4-12
Maintenance screen - Set..................................... 3-75
Maintenance time caution lamp............................ 3-30
Manual operation - Stop......................................3-225
Manual stationary regeneration - Operate.......... 3-114
Message - Check.................................................. 3-85
Message - Reply................................................... 3-86
Message display........................................... 3-36,3-85
Meter display.........................................................3-39
Method for adjusting........................................... 3-152
Method for checking before starting....................3-140
Method for operation when using general attachment
1 (e.g. crusher................................................6-28
Method for operation when using general attachment
2 (e.g. clamshell rotation, crusher rotation)... 6-29
Method for removing and installing revolving warning
lamp............................................................. 3-244
Method for steering machine.............................. 3-186
Mirror - Install...................................................... 3-243
Mirror - Remove.................................................. 3-242
Mirror - Remove / Install......................................3-242
Mirrors - Adjust....................................................3-156
Monitor settings.....................................................3-76
Monitor switches................................................... 3-43
Nitrogen gas charge pressure (for breaker) - Check /
Release..........................................................4-61
No jumping on or off machine............................... 2-21
No people on attachments.................................... 2-21
Noise.......................................................................1-5
Observance of the applicable laws and regulations,
exemption.................................................... 3-137
OFF switch..........................................................3-218
Oil............................................................................4-5
Oil filler cap - Install.............................................3-145
One-touch power maximizing function - Use...... 3-192
One-touch power maximizing pilot lamp............... 3-35
One-touch power maximizing switch.................... 3-89
Only authorized personnel.................................... 2-42
Operation of quick coupler...................................... 6-4
Operation record - Check......................................3-60
Operation with cold air to face and warm air to feet -
Start............................................................. 3-226
Operator ID........................................................... 3-82
Operator's seat - Adjust...................................... 3-152
Other equipment................................................... 3-98
Other precautions................................................. 2-52
Other trouble....................................................... 3-266
Outline of KOMTRAX..........................................3-136
Outline of maintenance........................................... 4-5
Overload caution lamp.......................................... 3-31
Pedal and oil flow of machine equipped with attach-
ment - Operate...............................................6-20
Perform KOWA (Komatsu Oil Wear Analysis)........ 4-7
Periodic replacement of defined life parts.......2-50,7-2
Permissible depth of water soil and dirt.............. 3-197
Phenomena and actions for chassis................... 3-267
Phenomena that are not failures.........................3-260
Pilot display...........................................................3-33
Pilot display and meter display............................. 3-32
Pivot turn - Operate.............................................3-186
Power button.......................................................3-230
Power supply outlet.............................................3-106
PPC circuit accumulator - Function.......................4-64
N
O
P
8-5