Epson Stylus Pro 9000 Series Manual page 7

Error conditions
Message/Light Explanation
COVER OPEN / Lower cover is open.
Pause light on
You are replacing the ink
INK COMPART.
/ cartridge(s) and the ink
OPEN Pause
light on compartment cover is
open.
INK LOW/ Ink Ink cartridge(s) are
light(s) nearly empty (printing
Out
flashing continues).
/ Ink cartridge(s) are
INK OUT Ink Out
light(s) on empty (printing stops).
LOAD PAPER / Paper set lever is up
light while loading paper.
Paper Out
on
Paper source setting in
LOAD ROLL
PAPER print options is different
LOAD SHEET from control panel.
/
PAPER Paper
light on
Out
MAINTENANCE
A printer part will need
REQ. <error
to be replaced soon.
number>
MAINTENANCE The waste ink system is
REQ 0100
almost full.
Ink cartridge(s) not
NO INK
/ installed.
CARTRIDGE Ink
Out light(s) on
Wrong interface card
OPTION I/F
ERROR
installed.
PAPER JAM / Paper has jammed in the
Paper Out light printer.
flashing
/ Roll paper was not cut
PAPER NOT CUT
light completely.
Paper Out
flashing
Cut paper did not fall off.
Paper slipped and fed
PAPER NOT
STRAIGHT / into the printer at an
light angle.
Paper Out
flashing
/ No paper is loaded.
PAPER OUT
Paper Out light
Paper ran out.
on
Response
Close the lower cover.
Close the ink
compartment cover
when you are finished
replacing the ink
cartridge(s).
Replace ink cartridge(s)
indicated by
Ink Out
light(s). See page 9.
Replace ink cartridge(s)
indicated by
Ink Out
light(s). See page 9.
Pull the paper set lever
down after you load the
paper.
Make sure the right
paper is loaded and the
paper source setting is
the same on the control
panel and print options.
Note the error number
and contact EPSON.
Contact EPSON to
schedule service.
Install ink cartridges as
indicated by the lights.
See page 9.
Turn off the printer and
remove the card.
Remove the jammed
paper.
Cut the paper manually,
then remove the cut
paper from the printer.
Reload paper.
Remove the cut paper
from the printer. Reload
paper.
Reload paper, making
sure the edges are
straight and aligned with
both rows of holes.
Load paper.
Remove any printouts or
paper remaining in the
printer and load more
paper.
If the message appears
during a print job, reset
the printer by pressing
the button for 3
Pause
seconds. Then load
paper and resend the
job.
8/00
EPSON Stylus Pro 9000 series
Message/Light Explanation
Paper set lever was
PUSH LEVER
DOWN/ Paper
released during the
Out light on
printing process or
another operation.
/ Paper could not be
RELOAD PAPER
light reversed into the
Paper Out
on printing position.
Image is too wide for
the paper loaded in the
printer.
Paper is not fully
ejected.
PAPER NOT CUT
was cleared.
REMOVE PAPER / Paper is too thick for
light print head cleaning.
Paper Out
on
An error has occured.
SERVICE REQ.
<error number> /
All lights flashing
SERVICE REQ. The waste ink system is
00000100/ full.
All lights flashing
TURN PWR OFF This message appears
AND ON
after you clear a paper
jam.
UNABLE TO You tried to print a test
PRINT
pattern while an error
condition was present or
the ink compartment
cover was open.
Wrong ink cartridge
WRONG
/ installed.
CARTRIDGE Ink
light(s) on
Out
EPSON Stylus Pro 9000 series - 7
Response
Push the paper set lever
down. Start printing
again from the beginning
for best results.
Remove the paper.
Reload it so that the
right and bottom edges
are straight and aligned
with both rows of holes.
Resize your image or
load wider paper.
Cut the paper at the
paper insertion slot, then
reload paper.
error Reload paper.
Push the paper set lever
down to remove the
paper. Print head
cleaning automatically
starts. After cleaning,
reload paper.
Note the error number,
and turn the printer off
and then on. If the
message remains,
contact EPSON.
Contact EPSON for
service.
Turn the printer off and
then on again.
After 3 seconds, the
message disappears.
Press the button
Pause
to exit SelecType mode.
If the message appears
again, clear the error
before you print.
Install the correct ink
cartridge(s).