go-e HOMEfix Installation And Operating Manual
Hide thumbs
Also See for HOMEfix:
- Operating instructions manual (28 pages) ,
- Quick reference manual (11 pages) ,
- Short instructions (4 pages)
Subscribe to Our Youtube Channel
Related Manuals for go-e HOMEfix
Summary of Contents for go-e HOMEfix
- Page 1 go-eCharger go-eCharger HOMEf i x HOMEf i x 11/22 kW INSTALLATION AND OPERATING GUIDE EN Version 3.0...
-
Page 2: Table Of Contents
1. Table of contents 1. Table of contents Table of contents/symbols .............3 Sustainable charging ..............4 Before installation and commissioning/download ....5 Safety regulations/notes............6 Product overview ..............9 Scope of delivery..............10 Technical data ................11 Installation ................14 Commissioning/charging .............18 10. LED status display/troubleshooting ........20 11. -
Page 3: Sustainable Charging
Note before installation and commissioning Note before installation and commissioning With the go-eCharger HOMEfix you have chosen an extremely compact and Observe all safety regulations and instructions in this manual! versatile charging station for electric vehicles. Smart and intelligent solutions Download the data sheet: www.go-e.co/downloads... -
Page 4: Safety Regulations/Notes
Removing and damaging warning notices attached to the go-eCharger or opening the device The Charger is only suitable for charging gassing vehicle traction batteries in well-ventilated will result in the loss of any liability by go-e GmbH. The warranty also expires in the event of any rooms. -
Page 5: Product Overview
The copyright for these operating instructions is owned by go-e GmbH. All texts and illustrations correspond to the technical status at the time of writing. go-e GmbH reserves the right to make unannounced changes. The content of the operating instructions does not justify any claims against the manufacturer. -
Page 6: Scope Of Delivery
7. Technical data 7. Technical data Product specifications Product specifications 11 or 22 kW charging box with 2 metres connection cable HOMEfix 11 kW HOMEfix 22 kW Dimensions Approx. 15 x 25 x 9 cm Weight 1.95 kg 2.47 kg 2 m, 5 x 2.5 mm²... -
Page 7: Technical Data
7. Technical data go-eCharger app and connectivity go-eCharger app and connectivity HOMEfix HOMEfix Remark 11 kW 22 kW HOMEfix 11 kW HOMEfix 22 kW Single-phase 1.4 kW 1.4 kW Country-specific limitations to 3.7 kW to 7.4 kW need to be observed... -
Page 8: Installation
8. Installation 8. Installation 8. Installation 8. Installation Benötigte Werkzeuge Benötigte Werkzeuge Drill holes at the four marked positions. Pencil Spirit level Measuring tape Drilling machine Screwdriver Hammer Cutter knife Side cutter Attach the wall bracket with four screws and do- Beiliegendes Befestigungsmaterial Beiliegendes Befestigungsmaterial wels each. - Page 9 • 3- or 4-pole for three-phase connection • 2-pole for single-phase connection The go-eCharger HOMEfix may be connected single-phase and three-phase. If necessary, lay an additional supply line. When selecting the cable cross-section, observe the simultaneity factor and the type of installation. We recommend the follo-...
-
Page 10: Commissioning/Charging
9. Commissioning/charging 9. Commissioning/charging 9. Commissioning/charging 9. Commissioning/charging Start of the charger Start of the charger Charging Charging The go-eCharger performs a self-test during initial After the car has enabled charging, the LEDs rot- start-up or after a restart, during which the LEDs ate clockwise around the type 2 socket during the light up in rainbow colours. -
Page 11: Led Status Display/Troubleshooting
10. LED status display/troubleshooting 10. LED status display/troubleshooting 10. LED status display/troubleshooting 10. LED status display/troubleshooting Activation required Activation required The go-eCharger displays the charging status via different colours and positions of the LEDs. In ad- The LEDs light up blue and two white LEDs dition, it executes a whole series of safety queries move from the top and bottom to the centre. - Page 12 It is possible that only 2 pha- ger app. This may take a few minutes. Do not dis- ses are connected. If no function occurs, contact connect the charger from the power supply during the go-e Support. this time. Firmware update successful Firmware update successful...
-
Page 13: Reset Card/Rfid Chip/Fine Wire Fuse
Disconnect the charger from the power supply beforehand. Only use original go-e fine wire fuses The delivered RFID chip is already learned. (one included in the scope of delivery). To authenticate a person authorised for charging, the chip needs to be held in front of the RFID reader before each charging process. - Page 14 WiFi the app. Otherwise, you need to select your network. Tap the „+“ icon in the go-e Charger go-eCharger in the app beforehand. app again. Select „Add an already set up go- eCharger“.
- Page 15 12. App - charging 12. App - charging 12. App - settings 12. App - settings The „Charging“ tab of the go-eCharger app gives You can adjust the basic and comfort settings of you direct access to the most important functions the charger via the „Settings“...
-
Page 16: Warranty And Exclusions
GmbH will send the customer a replacement box and will pay a total of up to 70 euros of After activating the scheduler, you can define the electrician’s costs incurred in uninstalling the defective charging station and installing the... -
Page 17: Ce Declaration Of Conformity
If you cannot find an answer to your question in this guide, on our website or in the app, please feel free to contact us: go-e GmbH Satellitenstraße AT 9560 Feldkirchen Mail: office@go-e.co Tel: +43 4276 6240010 www.go-e.co Deviating declaration of conformity for go-eChargers with serial numbers CC1- or CM-02- available at www.go-e.co/downloads...
Need help?
Do you have a question about the HOMEfix and is the answer not in the manual?
Questions and answers