BMPRO Trek3 Owner's Manual
  1. Manuals
  2. Brands
  3. BMPRO Manuals
  4. Monitor
  5. Trek3
  6. Owner's manual

BMPRO Trek3 Owner's Manual

Hide thumbs Also See for Trek3:
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL
Trek3
TEAMBMPRO.COM

Advertisement

Table of Contents
loading

Related Manuals for BMPRO Trek3

Summary of Contents for BMPRO Trek3

  • Page 1 OWNER’S MANUAL Trek3 TEAMBMPRO.COM...
  • Page 3 To learn more about the BMPRO range of products, please visit our website teambmpro.com TEAM BMPRO...

  • Page 4: Safety Precautions

    Correct installation is the most critical factor in ensuring the safe use of the Trek3. If every consideration of these instructions has been satisfied, the Trek3 will be safe to operate.

  • Page 6: Table Of Contents

    SAFETY PRECAUTIONS ..... 4 ABOUT THE TREK3 ..... . . 8 OPTIONAL ADD-ONS .

  • Page 8: About The Trek3

    For more information about Odyssey, refer to your Odyssey Owner’s Manual. Figure 1: The Odyssey system with Trek3 OPTIONAL ADD-ONS To get the most out of your Trek3, it may be used with the following products from the BMPRO range: 9 Dipper water level indicator...

  • Page 9: Trek3 System Diagram

    TREK3 SYSTEM DIAGRAM...

  • Page 10: Description Of Parts

    Displays the charging/discharging current and voltage of the caravan battery connected to the BatteryPlus35. The Battery display will flash if BMPRO’s BC300 External Shunt + CommLink has been installed and communication with the BC300 is lost. BATTERY CAPACITY BAR GRAPH Displays an estimate of the capacity of the connected battery, and underneath indicates if the battery is ‘CHARGING’...
  • Page 11 9 The BatteryPlus35 has automatically entered ECO mode to preserve battery   capacity until the battery can be charged. To reduce current draw from the battery, all other display segments on the Trek3 will turn off as well. BATTERY BUTTON Enables ECO mode which powers off all caravan loads connected to the BatteryPlus35 load terminal block, except for terminal 1.
  • Page 12 WATER PUMP BUTTON To turn the water pumps connected to the BatteryPlus35 on and off. When the BatteryPlus35 and Trek3 are first powered on, both pumps will be turned on as well. To turn pump 1 on/off, press the Water Pump button once.

  • Page 13: Mounting The Trek3

    MOUNTING THE TREK3 The Trek3 is designed to be mounted to the wall directly with screws. A hole for the connectors must be drilled before mounting. Flat head screws with a maxiumum diameter of 4.0mm must be used for mounting.

  • Page 14: Using Your Trek3

    USING YOUR TREK3 The Trek3 does not have an ON/OFF button. The Trek3 receives power directly from the BatteryPlus35 through the connected data cable. The Trek3 will automatically turn off if it is not receiving power from the BatteryPlus35. Upon start-up, the Trek3 will display...

  • Page 15: Trek3 Set-Up Mode

    . If the function can be edited, the menu function will flash on screen. EDIT Use the Battery button on the Trek3 to select a menu function or sub-function to edit. BACK Use the Home button on the Trek3 to return to the previous ‘Screen’ or menu function.
  • Page 16 Exiting Set-Up Mode To exit Set-Up mode or to exit from any menu function available in Set-Up mode, repeatedly press the BACK button until the Trek3 enters the Home screen. Alternatively, wait and the Trek3 will automatically revert to the Home screen, saving any changes made when editing the menu functions.

  • Page 17: Clock Menu Function

    Enter Set-Up mode and navigate to the CLOCK menu function. Follow the directions in figure 4 to set the time in 12-hour format on the Trek3 display. The AM and PM annunciators will automatically change as the hour changes from 11 to 12.

  • Page 18: Water Tank Menu Function

    8 to enable or disable the monitoring and display of a water tank with the Trek3. Figure 8: Enabling and disabling a water tank for monitoring and display with the Trek3 Configure Water Tank Type Enter Set-Up mode and navigate to the tanks menu function.

  • Page 19: Configuring Battery Capacity

    CONFIGURING BATTERY ALARM Configure the battery alarm and set the low battery voltage warning threshold to trigger the Battery Low warning on the Trek3 Home screen to indicate that the battery requires charging. By default, the low voltage warning threshold is 11V for lead acid batteries and 12.3V for LiFePO4 batteries.

  • Page 20: Lcd Backlight

    Figure 12: Configuring the LCD backlight brightness level FACTORY RESET Enter Set-Up mode and navigate to the FaCtOry menu function. Follow the directions in Figure 13 to perform a factory reset and restore the Trek3 to the factory settings. Figure 13: Factory reset...

  • Page 21: Servicing

    Trek3. Why are the battery volts and amp flashing on the Trek3? Battery volts and amps will flash on the Trek3 if a BC300 + CommLink external shunt has been installed and communication with the shunt has been lost.

  • Page 22: Appendices

    APPENDICES ADVANCED MENU FUNCTIONS Configure Battery Chemistry The ability to configure battery chemistry is available only if the Trek3 is in use with the BatteryPlus35-HA which is capable of charging both lead acid and LiFePO4 type batteries. By default, the BatteryPlus35-HA is configured to charge lead acid batteries.
  • Page 23 Adjusting Bulk Voltage The bulk voltage is the maximum voltage at which the BatteryPlus35 will charge the battery. The bulk voltage may be adjusted from 13.6 to 14.8V in steps of 0.1V. WARNING Changing the bulk voltage may result in the battery overcharging and cause damage to the battery and in extreme cases may also cause personal harm.

  • Page 24: Specifications

    SPECIFICATIONS TREK3 Input Voltage Range 8-15V Battery Drain < 21mA with backlight off Ambient Temperature 0-50°C Dimensions (mm) 164W x 108H x 22D...

  • Page 25: Compliance

    (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Any changes or modifications not expressly approved by BMPRO could void the user’s authority to operate this equipment.

  • Page 26: Warranty Terms And Conditions (Australia)

    Proof of purchase is required before you can make a claim under this warranty. HOW TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY: 3. The Trek3 is designed to be installed by a suitably qualified installer. You or your installer should carefully inspect the products before installation for any visible manufacturing defects. We accept no responsibility in addition to our consumer guarantee obligations where a product has been installed incorrectly.

  • Page 27: Limited Warranty Terms And Conditions (Usa)

    LIMITED WARRANTY TERMS AND CONDITIONS (USA) Registering your BMPRO product is an important step to ensure that you receive all the benefits you are entitled to. Please visit teambmpro.com to complete the online registration form for your new product today.
  • Page 28 BMPRO TEAM customerservice@teambmpro.com BMPRO 19 Henderson Rd, Knoxfield VIC 3180 Australia Unit 1, 821 E Windsor Ave, Elkhart IN 46514 USA .COM teambmpro.com...

Table of Contents