Install the ION 1000..................25 Rack Mount the ION 1000........................27 Wall Mount the ION 1000........................29 Install the ION 1000 by Replacing an Existing Router..............31 Install the ION 1000 With an Existing Router.................. 32 Install the ION 1000 in Control Mode....................33...
Before You Begin Read the following topics before you install or service a Palo Alto Networks next-generation ® firewall or appliance. The following topics apply to all Palo Alto Networks firewalls and appliances except where noted. > Tamper Proof Statement >...
• The integrity of the tamper-proof tape used to seal the box or crate is not compromised. • The integrity of the warranty label on the firewall or appliance is not compromised. ION 1000 HARDWARE REFERENCE | Before You Begin 2021 Palo Alto Networks, Inc.
ION 1000 Overview Learn about the Prisma SD-WAN ION 1000 and then plan your deployment. > ION 1000 > ION 1000 Ports > ION 1000 Front Panel with LEDs > ION 1000 Specifications > ION 1000 Compliance Statement > ION 1000 Installation Kit Components...
It also helps gain direct insight into end user application performance for traditional, SaaS, modern encrypted applications. Deploy the ION 1000 in a standalone fashion without a data center device, thereby, enabling granular control and visibility for direct-to-internet deployment scenarios.
ION 1000 Ports The ports on the ION 1000 are used as follows: Ports Description This port is an auxiliary access port intended for offline access, configuration, and troubleshooting of a system during installation. Internet/LAN/WAN Ports Ports 1- 4 are individual ports, used for internet, local area network (LAN), or multi-path label switching (MPLS) connectivity.
ION 1000 Front Panel with LEDs The Prisma SD-WAN ION 1000 LEDs indicate the following status: Icons Description Displays disk status. Orange light (Blinking)—Disk activity. Displays controller connectivity status. Green light—Connected. Red light—Not Connected. Displays power status. Green light—Powered On.
ION 1000 Specifications The ION 1000 device specifications are shown below: Feature Description WAN/LAN/Internet 4 x 10/100/1000 RJ-45 Throughput Throughput Up to 100 Mbps Encrypted throughput is measured with 1400 byte HTTP packets with all features turned on. Power and Mechanical...
ION 1000 Installation Kit Components The ION 1000 installation kit contains the following parts and tools to install the device: • 1x 36W power adapter. • 1x power cord, which varies depending on the country or region. The following optional hardware parts must be ordered separately: •...
Press the power switch 5 times (press and hold for 1 second, then, release) to shut down the device. Reboot the ION 1000 Press the power switch 3 or 4 times to reboot the ION 1000. ION 1000 HARDWARE REFERENCE | ION 1000 Overview...
Install the ION 1000 The ION 1000 can be installed to replace the existing router or deployed with an existing router without modifying any of the network settings at the remote office: > Rack Mount the ION 1000 > Wall Mount the ION 1000 >...
Rack Mount the ION 1000 Rack mount the ION 1000 on a standard 19 inch rack. The optional rack-mount kit includes two identical L- shaped brackets that you can attach to either side of the ION 1000 using screws. Gather the L-shaped rack-mounting brackets.
Gather the wall mounting brackets, also referred to as the ear brackets. These brackets enable you to anchor the ION 1000 to the wall. STEP 2 | Place the ION 1000 upside down and locate the four (4) screw holes on each corner of the device. STEP 3 | Place the ear brackets on each side of the device and align the screw holes on the bracket and the device.
Configure the ION 1000 as a drop-in replacement for the WAN Router. This mode is most useful for saving cost at new sites that are designed without a traditional router in mind.
Install the ION 1000 With an Existing Router Install the Prisma SD-WAN ION 1000 with an existing router. This allows you to insert the ION 1000 without modifying any network settings at the remote location. ION 1000 HARDWARE REFERENCE | Install the ION 1000 2021 Palo Alto Networks, Inc.
Install the Prisma SD-WAN ION 1000 in control mode. STEP 1 | Plan and prepare for cabling and connection of the ION 1000 to insert it into your network. Ensure that internet access using a private WAN connection or direct internet broadband is available at your site to allow remote configuration of the ION 1000.
Page 34
ION 1000 HARDWARE REFERENCE | Install the ION 1000...
Need help?
Do you have a question about the ION 1000 and is the answer not in the manual?
Questions and answers