Download Print this page
WaterLogic WLH2 Classe Quick Start Manual
Hide thumbs Also See for WLH2 Classe:

Advertisement

Quick Links

Read and follow all safety information carefully. The signal words used in this manual are
selected as shown below and based on an assessment of the degree of potential injury or
damage (severe or minor) and the occurrence of injury (definitely occurs or has the potential to
occur) when the warning is ignored:
DANGER!
Indicates a situation which, when not avoided, results in death or severe injury.
WARNING!
Indicates a situation which, when not avoided, has the potential to result in death or
severe injury; and/or severe property damage.
CAUTION!
Indicates a situation which, when not avoided, results or has the potential to result in
minor injury; and/or minor property damage.
Basic safety precautions should be followed, including the following:
Ensure all Local, State, and Federal Laws and Codes including health and safety guidelines are
met when installing Waterlogic Equipment. Only qualified service technicians should attempt
installation and service of Waterlogic Equipment. Always read the entire operating instructions
before using the appliance and save these instructions for future use.
DANGER!
This product can cause death or severe injury if incorrectly operated, installed or
maintained. The installation, maintenance, sanitizing and any repair must be performed by
qualified persons trained by Waterlogic International or their approved distributors only. Do
not remove any panel or cover to protect against electrical shock and exposure to UV
radiation.
DANGER!
ELECTRICAL SHOCK HAZARD. Always use a dedicated and properly grounded
outlet. Unit should be protected by ground-fault circuit interrupter (GFCI) or residual current
device (RCD) having a rated residual operating current not exceeding 30mA. Use only
Waterlogic supplied power cord. Never use extension cords or power strips to connect unit.
Do not use if the power supply cord is damaged. Always unplug from power supply prior to
servicing.
WARNING!
AUTHORIZED USE ONLY. This appliance is to be used for its intended purpose as
described in this manual. Untrained individuals who use this manual assume the risk of any
resulting property damage or personal injury. This appliance can't be used by children and
persons with reduced physical, sensory or mental capabilities or lack of experience.
WARNING!
UV-C EMITTER (UV LAMP). This appliance contains a UV-C emitter (UV Lamp).
UV-C radiation may, even in small doses, cause harm to the eyes and skin. Unintended use or
damage to the housing may result in the escape of dangerous UV-C radiation. Never operate
the UV-C emitter if damaged or removed from enclosure. Do not touch or look directly into
the faucet.
WLH2 Classe Manual
SAFETY ALERT SYMBOLS
SAFETY PRECAUTIONS
Page 4 – Revision: 3-2-2021

Advertisement

loading

Summary of Contents for WaterLogic WLH2 Classe

  • Page 1 (RCD) having a rated residual operating current not exceeding 30mA. Use only Waterlogic supplied power cord. Never use extension cords or power strips to connect unit. Do not use if the power supply cord is damaged. Always unplug from power supply prior to servicing.
  • Page 2 WARNING! DO NOT OPERATE IF DAMAGED. Unplug and isolate water supply if abnormal conditions exist. Contact Waterlogic or authorized dealer for repair, service, and installation to avoid hazards. WARNING! CONNECT TO POTABLE WATER SUPPLY. This system is to be used for water only and is not intended for use where water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system.
  • Page 3 Ice Bath Drain Port The WLH2 Classe is equipped with a drain port to the ice bath. This makes for easier maintenance as well to ease transport if needed. Energy Saver The WLH2 Classe comes from the factory with Energy Saver active.
  • Page 4 Drinking Water Coolers. CSA C22.2 No. 120 CSA Standard for Refrigeration BPA Free - Waterlogic tests for BPA and declares that all of its products are Bisphenol-A FREE and contain no harmful BPA plastics. NSF/ANSI-55 Class A – Ultraviolet Microbiological Water Treatment System NSF / ANSI 372 –...
  • Page 5: Specifications

    MODEL/PART DESIGNATIONS MODEL - BRAND NAME DESCRIPTION PART NUMBER WLH2 Classe – Cold, Cold Sparkling WLH2 Classe F-H2FX-M-CS-IB-SB-WLU CLASSE WLH2 Serial Number: TH2C434SBXXX SPECIFICATIONS ITEM WHL2 CLASSE Water Connection 1/4” Quick Connect Cold Water Temperature Cold Water Temperature – Factory Set Point 5°C (41°F)
  • Page 6: Shipping Specifications

    ELECTRICAL SUPPLY 120V/60Hz 15 Amp Service COMPONENT POWER (approximate) AMP DRAW (approximate) Pump 267w 0.5A Mixing Motor 0.3A Control Power 0.2A Compressor 220w UV Lamp System 0.6A WLH2 Classe TOTAL 617w 5.6A WLH2 Classe Manual Page 9 – Revision: 3-2-2021...
  • Page 7 OPERATING INSTRUCTIONS The WLH2 Classe utilizes a very simple user interface. 4 main buttons across the front user panel. The first two buttons (red/yellow) can be used to dispense cold Sparkling water and the last two (green/blue) are used to dispense cold Still water. Each of the buttons are programmed to dispense a preset volume of water and can be reprogrammed if desired.
  • Page 8 5 seconds and the LEDs will return to solid light. (Maximum dispensing is 3liters.) NOTE: Factory presets for the small and large dispense buttons are 750ml and 1000ml respectively. WLH2 Classe Manual Page 11 – Revision: 3-2-2021...
  • Page 9 (48) months from the date of manufacture. Waterlogic Commercial Products, LLC (“Waterlogic”) based in the U.S.A. and its affiliated companies are not liable for any cost of removal, installation, transportation, or any other charges which may arise in connection with a warranty claim.