Download
Share
Print this page
Omega LINKR-M1 Installation And Test Manual
  1. Manuals
  2. Brands
  3. Omega Manuals
  4. Controller
  5. LINKR-M1
  6. Installation and test manual

Omega LINKR-M1 Installation And Test Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Quick Reference - LINKR-M1 Install Overview
1
2
3
4
5
6
7
LINKR-M1 install guide EN A6.indd 1
Installation And Testing Guide
(ENGLISH / INGLÉS)
Download the Linkr app to your smartphone.
Search 'omega linkr' in your app store - iphone &
android only.
Mount the Linkr module with the label facing the sky.
There cannot be metal between the module and sky.
Make all necessary wiring connections.
See "Connecting the device" on page 4 for
After 30 seconds with the vehicle ignition ON, check the
indicator lights to make sure the unit has cellular service
and GPS signal.
Login at www.omegadealer.com to temporarily activate
the device for testing.
Add the device to your Linkr app to configure & test.
See "Testing the device" on page 10.
Write the configuration code & device info on the back
cover of this manual and give it to the vehicle's owner.
U S A S M A R T P H O N E
V E H I C L E I N T E R F A C E
See page 9 for LED status definitions
Detailed instructions on the following pages >
details.
5/24/2016 4:00:51 PM

Advertisement

loading

Related Manuals for Omega LINKR-M1

Summary of Contents for Omega LINKR-M1

  • Page 1 (ENGLISH / INGLÉS) Quick Reference - LINKR-M1 Install Overview Download the Linkr app to your smartphone. Search ‘omega linkr’ in your app store - iphone & android only. Mount the Linkr module with the label facing the sky. There cannot be metal between the module and sky.

  • Page 2: Indicator Lights

    A USB interface cable is available for purchase. It is rarely needed but allows you to update the device firmware manually. Otherwise, the user can update firmware from their phone app (appropriate service plan required). LINKR-M1_EN-4/22/16 LINKR-M1 install guide EN A6.indd 2 5/24/2016 4:00:51 PM...
  • Page 3 BLACK 4-Pin Serial Data Connector (required): This allows for a quick plug-in installation when used with a compatible Omega security or remote start system. Plug this into the matching port on the host system and program the data port for iDatalink protocol.
  • Page 4 7 negative pulses within 10 seconds. Connect this to the alarm’s horn honk output or flashing light output. NOTE: Omega security systems will send alarm trigger status on the data port, in which case, this wire is not connected.
  • Page 5 This is a negative pulse 150mA output (add a relay if necessary) configurable for 0.8 second, 3 second, or 10 second pulse. It can be assigned to most command buttons in the Linkr app. LINKR-M1_EN-04/22/16 LINKR-M1 install guide EN A6.indd 5 5/24/2016 4:00:51 PM...
  • Page 6 ESTE LADO HACIA EL CIELO OUT2 Indicator Lights CEL GPS PWR BATT Backup Battery* USB Port On/Off Switch (for update by PC- optional cable required) *backup battery unavailable on some versions LINKR-M1_EN-4/22/16 LINKR-M1 install guide EN A6.indd 6 5/24/2016 4:00:51 PM...

  • Page 7: Typical Installation

    Starter Interrupt Panic/Override Socket & Relay ORANGE Button (not included) WHITE Ground cut starter wire To Ignition To Starter Switch WIRE LEGEND Hard wire connection required Supported via DATA port(s) LINKR-M1_EN-04/22/16 LINKR-M1 install guide EN A6.indd 7 5/24/2016 4:00:51 PM...
  • Page 8 PINK serial data wire (DO NOT CONNECT): This wire has no function in a hardwire installation. BLACK/WHITE serial data wire (DO NOT CONNECT): This wire has no function in a hardwire installation. LINKR-M1_EN-4/22/16 LINKR-M1 install guide EN A6.indd 8 5/24/2016 4:00:51 PM...
  • Page 9 GPS data error GPS is off connected (blue) Power Power connected, Power is not connected internal battery is connected, backup No Power & battery is (red) charging battery is ON. charged LINKR-M1_EN-04/22/16 LINKR-M1 install guide EN A6.indd 9 5/24/2016 4:00:52 PM...
  • Page 10 Step 4: Test The Device Install the Linkr app on your smartphone. search “Omega Linkr” in the app store. Login at www.omegadealer.com to activate the device for install testing. This can be done from your phone or computer. Press “add” on the App’s home screen & follow the on-screen intructions to enter test mode.
  • Page 11 LINKR-M1 install guide EN A6.indd 11 5/24/2016 4:00:52 PM...
  • Page 12 LINKR-M1 install guide EN A6.indd 12 5/24/2016 4:00:52 PM...