Related Manuals for Hisense HK560M
Summary of Contents for Hisense HK560M
- Page 1 HK560M User’s Manual Document version 1.0 QingDao Hisense Intelligent Commercial System Co.,Ltd.
- Page 2 Safety Notices Before Installation or Use ☆ It is required grounded well and the supply voltage shall be stable, and you must confirm that the voltage of the outlet provides shall be in line with the voltage marked on the label of the unit.
- Page 3 Product standard Name: POS device 1. Applied range The HK560M terminal adopt open operating system, flexible component structure and standard peripherals. The products are suitable for the commercial enterprises, such as restaurants, supermarkets, and convenience stores to Internet –connected use or stand-alone use. The main components are standard parts, so the quality of the products is reliable, the system is easy to upgrade and the components are conveniently and easily maintained.
- Page 4 I/O Ports 1 * RJ-45 (100M/1000Mbps Gigabit LAN) HDMI 1*HDMI Port Audio 1 * Line-out Cash Drawer 1 * RJ-11 for cash drawer Power Power Adapter Adapter (DC 24V, 2.5A)(Standard) Adapter (DC 24V, 5A) (optional) 2*20 characters Second Display 15.6 inch (touch/non-touch) Peripheral 12.5 inch(touch/non-touch) 10.1inch(touch/non-touch)
- Page 5 3).Remove the two connectors shown in the picture and protect them with the tape according to the picture shows (to prevent the connector from being pulled out in the process of dismantling and threading); 4).Rotate the main screen and the secondary screen : to the vertical angle, remove the three screws of the main screen hinge and the second screen hinge respectively, and carefully pass the screen line through the line hole.
- Page 6 5).Remove the hinges of the host: Remove four screws according to the picture shows. Remove the hinges of the host and the hinges cover of the host separately. 6).Remove the extended interface cover: pull the expanded interface cover outward at the notch according to the picture shows, and remove it.
- Page 7 Environmental requirements Type State Voltage AC 100V-240V 50-60Hz Bipolar Environmental Temperature 5℃ - 40℃ Optimal 40% - 90% Size specification Single screen，Length×Width×Height：405*210*330；Flip Angle 0-45° Double Screen，Length×Width×Height：405*250*370；...
- Page 8 Main Flip Angle 0-45°，Second screen Flip Angle 0-30° High position +printer，Length×Width×Height：405*250*420 Self-service，Length×Width×Height：230*250*450 Open the box and check. Before opening the box, check whether the box is in good condition, and whether there is any obvious damage. 2) The equipment must be installed by technical service person or distributors. Operation 1) Switching Instructions：...
-
Page 9: Printer Operations
When swiping the card, the machine should be placed on a hard horizontal plane. Please swipe the magnetic strip of the magnetic strip card inward from the swipe slot. The process of card swiping should be smooth and uniform. 4) Contactless card operation：... - Page 10 2) Load and change paper introduction Press the open button to open the paper bin cover, as shown below. If there are paper tubes in the paper warehouse, please take them out. b. Put the paper roll into the paper bin, pay attention to the correct direction of the paper roll. c.
- Page 11 d. Remove excess paper toward the side of the paper cut. Paper rolling Requirements of the thermal paper： Type：Thermal paper Width of paper：57.5±0.5mm / 79.5±0.5mm Outside Diameter of paper roll：Max 83mm Thickness of Thermal Paper：0.056 ~ 0.13mm 2) Recommendation of thermal Paper Model： Type Manufacture FD210,PD150R,PD160R...
-
Page 12: Printer Maintenance
A. Please use the recommended paper roll or the same quality paper roll. The use of other types of paper roll may affect the printing effect and the life of the printing head. B. If the paper roll is contaminated by chemicals or oil, the contaminated part of the paper roll may fade or the printing effect is not clear. -
Page 13: Fcc Warning Statement
FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Need help?
Do you have a question about the HK560M and is the answer not in the manual?
Questions and answers