Advertisement
Quick Links
Advertisement
Related Manuals for Hisense HK316
Summary of Contents for Hisense HK316
- Page 1 HK316 User’s Manual Document version 1.3...
- Page 2 Safety Notices Before Installation or Use ☆ It is required grounded well and the supply voltage shall be stable, and you must confirm that the voltage of the outlet provides shall be in line with the voltage marked on the label of the unit.
- Page 3 1. Applied range The HK316 terminal adopt open operating system, flexible component structure and standard peripherals. The products are suitable for the commercial enterprises, such as restaurants, supermarkets, and convenience stores to Internet –connected use or stand-alone use. The main components are standard parts, so the quality of the products is reliable, the system is easy to upgrade and the components are conveniently and easily maintained.
- Page 4 1、24V power input 2、Cash drawer interface 3、Serial port 4、printer 24V power 5、USB*2 6、USB*2 7、RJ45 8、Audio 9、Volume+ button 10、Volume - button 11、Brightness+ button 12、Brightness - button 13、TF card slot 14、Micro USB 15、USB...
-
Page 5: Main Board
3. Mainboard Mainboard front layout: Ports and definition Ports Interface Item 1.CON25 Serial port wafer1.25 1*8pin x1set MSR and RFID 2.CON65 Serial port 12PIN FPC socket Power On/Off 3.CON4 Button board pin wafer2.0 2*6 pin x1set Power On/Off （reserved） 4.CON23 CON24 Serial port COM0 pin wafer2.0 2*5 pinx1set COM0 Serial port COM2 pin wafer2.0 2*5 pinx1set... - Page 6 Mainboard back layout Edp1 interface definition Pin No. Function Pin No. Function Enable Lane1_N Lane1_P Lane0_N Lane0_N AUX_CH_P AUX_CH_N...
- Page 7 EDP2 interface definition Pin No. Function Pin No. Function Enable Lane1_N Lane1_P Lane0_N Lane0_N AUX_CH_P AUX_CH_N Audio interface definition Audio Description Audio Code ES8388 Rear IO Type HP Connector PIN defined Onboard audio pin SPK_LP SPK_LN 1■ 2● 3● 4● SPK_RP SPK_RN PIN Type...
- Page 8 4. Device Assembly and disassembly 1). Unscrew the two screw shown to remove the back shell of the base. 2).After removing the screw, pull at the back shell of the base according to the picture shows, and remove the back shell of the base.
- Page 9 screen hinge and the second screen hinge respectively, and carefully pass the screen line through the line hole. Separate the main and auxiliary screen from the base respectively. 5).Remove the hinges of the host: Remove four screws according to the picture shows. Remove the hinges of the host and the hinges cover of the host separately.
- Page 10 8).Remove 7 screws according to the picture shows to remove the host fixed seat, so that the motherboard can be replaced and maintained. 5. Functional testing and parameter setting of peripherals In product test mode, magnetic stripe card test items are swiped by magnetic stripe card, and magnetic stripe card corresponding to the track shows "success"...
-
Page 11: Cash Drawer
Contactless card test items In product test, with RFID card close to the back of the card reader, show "find * card" (Contactless card is divided into A card, B card, M card). As The following figure. Printer U-port printer, without setting baud rate, can use the normal detection of product test procedures. Cash drawer As shown below, for the item "CashBox ByCPU"... - Page 12 Environmental requirements Type State Voltage AC 100V-240V 50-60Hz Bipolar Environmental grounding Temperature 5℃ - 40℃ Optimal 40% - 90% Size specification Single screen，Length×Width×Height：405*210*330；Flip Angle 0-45°...
- Page 13 Double Screen，Length×Width×Height：405*250*370； Main Flip Angle 0-45°，Second screen Flip Angle 0-30° High position +printer，Length×Width×Height：405*250*420 Self-service，Length×Width×Height：230*250*450 Open the box and check. Before opening the box, check whether the box is in good condition, and whether there is any obvious damage. The equipment must be installed by technical service person or distributors. Operation Switching Instructions：...
-
Page 14: Printer Operations
Start-up: When the adapter is connected, hold down the switch button on the right back side of the bottom of the machine for about 3 seconds. When the screen is on and the button indicator light is on, the startup can be realized. Shutdown: Press the switch button on the right back side of the bottom of the machine for about 3 seconds, and operate according to the screen prompt, which can realize shutdown and restart functions. - Page 15 Load and change paper introduction Press the open button to open the paper bin cover, as shown below. If there are paper tubes in the paper warehouse, please take them out. b. Put the paper roll into the paper bin, pay attention to the correct direction of the paper roll.
- Page 16 c. Please take out a small amount of paper from the front of the roll and close the cover of the printer's paper bin d. Remove excess paper toward the side of the paper cut. Paper rolling 1) Requirements of the thermal paper： Type：Thermal paper...
-
Page 17: Printer Maintenance
Width of paper：57.5±0.5mm / 79.5±0.5mm Outside Diameter of paper roll：Max 83mm Thickness of Thermal Paper：0.056 ~ 0.13mm 2) Recommendation of thermal Paper Model： Type Manufacture FD210,PD150R,PD160R OJI Paper CO., Notes： A. Please use the recommended paper roll or the same quality paper roll. The use of other types of paper roll may affect the printing effect and the life of the printing head. - Page 18 10. Accessories Note Item Unit Quantity POS terminal Power adaptor Power cable FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the HK316 and is the answer not in the manual?
Questions and answers