Related Manuals for Hisense HK560
Summary of Contents for Hisense HK560
- Page 1 HK560 User’s Manual Document version 1.0 QingDao Hisense Intelligent Commercial System Co.,Ltd.
- Page 2 Safety Notices Before Installation or Use ☆ It is required grounded well and the supply voltage shall be stable, and you must confirm that the voltage of the outlet provides shall be in line with the voltage marked on the label of the unit.
- Page 3 1. Applied range The HK560 terminal adopt open operating system, flexible component structure and standard peripherals. The products are suitable for the commercial enterprises, such as restaurants, supermarkets, and convenience stores to Internet –connected use or stand-alone use. The main components are standard parts, so the quality of the products is reliable, the system is easy to upgrade and the components are conveniently and easily maintained.
-
Page 4: Main Board
2. I/O port view 1、24V Power in 2、cash drawer(24V) 3、Powered USB(24V) 4、USB*2 5、USB*2 6、COM1 7、COM2 8、COM3 9、LAN 10、audio 3. Mainboard Mainboard front layout:... - Page 5 Jumpers / Headers and Connectors SYS_FAN1 System Fan Connector CLR_CMOS1 CMOS Clear Jumpe J_VGA1 VGA Pin Heade J_COM4, J_COM5, J_COM6 COM4-6 Pin Headers F_USB1 Front USB2.0 Pin Header1 J_PWRCOM4 COM4 VCC Select Jumpe F_USB2 Front USB2.0 Pin Header2 F_USB3 Front USB2.0 Pin Header3 F_USB4 Front USB2.0 Pin Header4 F_PANEL1...
- Page 6 R_USB1(R_USB5) POWER USB 24V Key-2 Connector (USB2.0 TYPE-A Connector) R_USB2 USB2.0 Dual TYPE-A Connector R_USB3 USB3.0+USB2.0 TYPE-A Connector COM1 COM1 RJ50 Connector COM2 COM1 RJ50 Connector COM3 COM1 RJ50 Connector RJ45_1 LAN RJ45 Connector Line-out 3.5mm Jack EDP1 (EDP1 Signal Connector 40*1 Pin 0.50mm) EDP2 (EDP2 Signal Connector 40*1 Pin 0.50mm)
- Page 7 J_VGA1 (VGA Pin Header 12*2 Pin 2.00mm)
- Page 8 J_PWRCOM4 (COM4 VCC Select Jumper 3*2 Pin 2.54mm) CLR_CMOS1 (CMOS Clear Jumper 3*1 Pin 2.54mm)
- Page 9 4. Device Assembly and disassembly 1). Unscrew the two screw shown to remove the back shell of the base. 2).After removing the screw, pull at the back shell of the base according to the picture shows, and remove the back shell of the base.
- Page 10 4).Rotate the main screen and the secondary screen : to the vertical angle, remove the three screws of the main screen hinge and the second screen hinge respectively, and carefully pass the screen line through the line hole. Separate the main and auxiliary screen from the base respectively. 5).Remove the hinges of the host: Remove four screws according to the picture shows.
- Page 11 7. remove the hard drive, unscrew the hard drive fixing screw, then remove the hard drive as arrow direction show in the picture below. 8.remove the host back cover, remove the screws of hinge cover(4 pcs, show as ① ) and screws of back cover(4 pcs, show as ②...
- Page 12 Voltage AC 100V-240V 50-60Hz Bipolar Environmental Temperature 5℃ - 40℃ Optimal 40% - 90% Size specification Single screen，Length×Width×Height：405*210*330；Flip Angle 0-45° Double Screen，Length×Width×Height：405*250*370； Main Flip Angle 0-45°，Second screen Flip Angle 0-30° High position +printer，Length×Width×Height：405*250*420...
- Page 13 Self-service，Length×Width×Height：230*250*450 Open the box and check. Before opening the box, check whether the box is in good condition, and whether there is any obvious damage. 2) The equipment must be installed by technical service person or distributors. Operation 1) Switching Instructions： Start-up: When the adapter is connected, hold down the switch button on the right back side of the bottom of the machine for about 3 seconds.
-
Page 14: Printer Operations
4) Contactless card operation： Contactless card induction zone is located behind the right side of the host (with the contactless mark printed). When need read contactless card, please place the card above the induction zone. Printer operations Printer Structure... - Page 15 2) Load and change paper introduction Press the open button to open the paper bin cover, as shown below. If there are paper tubes in the paper warehouse, please take them out. b. Put the paper roll into the paper bin, pay attention to the correct direction of the paper roll. c.
- Page 16 d. Remove excess paper toward the side of the paper cut. Paper rolling Requirements of the thermal paper： Type：Thermal paper Width of paper：57.5±0.5mm / 79.5±0.5mm Outside Diameter of paper roll：Max 83mm Thickness of Thermal Paper：0.056 ~ 0.13mm 2) Recommendation of thermal Paper Model： Type Manufacture FD210,PD150R,PD160R...
-
Page 17: Printer Maintenance
A. Please use the recommended paper roll or the same quality paper roll. The use of other types of paper roll may affect the printing effect and the life of the printing head. B. If the paper roll is contaminated by chemicals or oil, the contaminated part of the paper roll may fade or the printing effect is not clear. - Page 18 FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.