Viessmann Vitosol-F Installation Instructions For Contractors
Flat-plate collector for pitched roofs and above roof installation with rafter flange
Hide thumbs
Also See for Vitosol-F:
- Installation instructions manual (80 pages) ,
- Installation instructions for contractors (24 pages) ,
- Service instructions manual (24 pages)
Related Manuals for Viessmann Vitosol-F
Summary of Contents for Viessmann Vitosol-F
- Page 1 VIESMANN Installation instructions for contractors Vitosol-F Type SV and SH Flat-plate collector for pitched roofs and above roof installation with rafter flange VITOSOL-F Dispose after installation. 5465 446 GB 2/2014...
- Page 2 Safety instructions Please follow these safety instructions closely to prevent accidents and material losses. Safety instructions explained Please note This symbol warns against the risk of material losses and environmental pollution. Note Details identified by the word "Note" contain additional information.
-
Page 3: Table Of Contents
Index Intended use ........................Preparing for installation Components ..................Dimensions .................... Horizontal distribution of rafter flanges ..........■ Dimensions for vertical arrangement of rafter flanges ......■ Installation sequence Mounting the fixing system ..............Installing the collectors ................10 Connecting the collectors ..............11 Installation .................... -
Page 4: Intended Use
Intended use The appliance is only intended to be installed and operated in sealed unvented systems that comply with EN 12828 / DIN 1988, or solar thermal systems that comply with EN 12977, with due attention paid to the associated installation, service and operating instruc- tions. -
Page 5: Preparing For Installation Components
Components Fig. 1 Rafter flange Vitosol-F x in mm Seal Type SV Subject to the number of collectors: Screws 1109/2186 Mounting rail Type SH 2433 Rail connectors Mounting plate Clamping bracket Dimensions Horizontal distribution of rafter flanges A specific number of rafter flanges is allocated to each Example: number of collectors. - Page 6 Dimensions (cont.) 1 collector 2 rafters are required for all snow loads. 2 collectors Rafter spacing in mm Snow load in kN/m 0.75 1.25 ≤ ≤ 1, 4 1, 2, 4 ≤ 1, 3 1, 2, 3 ≤ 1, 3 1, 2, 3 ≤...
-
Page 7: Dimensions For Vertical Arrangement Of Rafter Flanges
Dimensions for vertical arrangement of rafter flanges Fig. 3 Maximum deviation from dimensions x and y 10 mm b: Distance between the lower mounting rails when several collectors are installed above each other. Vitosol-F a in mm b in mm Type SV 1750 2080 2400 –... -
Page 8: Installation Sequence Mounting The Fixing System
Mounting the fixing system Fig. 4 Fig. 5... - Page 9 Mounting the fixing system (cont.) 90° Fig. 6 Information on step 5: From a certain number of collectors upwards, 2 mount- ing rails will need to be joined with a rail connector. Fig. 7 Lower mounting rail...
-
Page 10: Installing The Collectors
Mounting the fixing system (cont.) Type SV Number — — Type SH Number 2265 2268 2268 2268 2268 2268 2268 2268 2271 2271 2271 2271 2271 2271 — — Installing the collectors Fig. 8 Installation information Please note The first and last collector must be positioned with The connection pipes must be free of any signs ■... -
Page 11: Connecting The Collectors
Installing the collectors (cont.) 90° Fig. 10 Connecting the collectors Fig. 11 Fig. 12 Note The collector temperature sensor is part of the stand- ard delivery of the solar control unit. Installation information Initially turn the union nut by hand, then tighten with ■... -
Page 12: Installation
Soft solder could be weakened, particularly near the collectors, due to the maximum temperatures that may occur there. Metal seal connections, locking ring fittings or Viessmann plug-in connections with double O-rings are the most suitable. Should alternative seals be used, such as flat gas-... -
Page 13: Commissioning
Stagnation heat sink Non-return valves Expansion vessel Solar circuit pump Drip pan Air separator Collector Shut-off valve (adjusting screw above flow indica- Solar control unit DHW cylinder Drain valve Cylinder temperature sensor Flow indicator Collector temperature sensor Commissioning "Vitosol-F" service instructions. - Page 16 Viessmann Werke GmbH&Co KG Viessmann Limited D-35107 Allendorf Hortonwood 30, Telford Telephone: +49 6452 70-0 Shropshire, TF1 7YP, GB Fax: +49 6452 70-2780 Telephone: +44 1952 675000 www.viessmann.com Fax: +44 1952 675040 E-mail: info-uk@viessmann.com...