Table of Contents
Advertisement
Quick Links
DRC810DT
SPDT Dry Contact Relay Controller
Installation Manual
Warning..................................................... 2
Features..................................................... 2
Important Safeguards................................... 2
Internal View............................................... 3
Mounting.................................................... 4
Supply & Load Cable Connections................... 5
Connecting Serial Control Cables.................... 6
WMGD Pty Limited trading as Dynalite ABN 33 097 246 92
Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia
t +61 8338 9899
f +61 2 8338 9333
contents
Hardware Controls.............................................8
Troubleshooting................................................9
Specification.....................................................9
dynalite.info@philips.com
dynalite-online.com
Advertisement
Table of Contents
Related Manuals for Philips Dynalite DRC810DT
Summary of Contents for Philips Dynalite DRC810DT
-
Page 1: Table Of Contents
Supply & Load Cable Connections.……………… 5 Connecting Serial Control Cables……………….. 6 WMGD Pty Limited trading as Dynalite ABN 33 097 246 92 Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia t +61 8338 9899 f +61 2 8338 9333 dynalite.info@philips.com dynalite-online.com... -
Page 2: Warning
important safeguards Warning – This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate Warning measures. TO REDUCE THE RISK OF FIRE OR Read Instructions –... -
Page 3: Internal View
Rs485 DyNet / DMX512 Serial Port Connections Control CPU Knock Out For Network Socket Low Voltage Cable Service Switch Depth 75mm For spare parts or service, please call your local Philips Dynalite Dealer, and specify DRC810DT DRC810DT Installation Manual Rev I.docx... -
Page 4: Mounting
mounting Select a Suitable Location This device is designed for indoor use only. If installing external location, DRC810DT must be housed in a suitable well-ventilated enclosure. Choose a dry location, that will be accessible after the installation is complete. The DRC810DT should be mounted vertically, the right way up. -
Page 5: Supply & Load Cable Connections
supply and load cable connections Supply Cables The supply input terminals are located toward the top left of the enclosure and consists of Neutral, Line, and an Earth link located on the chassis, all of which will accept up to cables. -
Page 6: Connecting Serial Control Cables
connecting serial control cables Connect Data Cable in a ‘Daisy Chain’ Determine Your Requirements Serial Ports are used to interconnect other dimmers, smart control panels, sensors and AV controllers. Serial port devices can be identified by 4 terminals, labelled: GND, DATA + DATA -, +VE. - Page 7 connecting load cables Example of load wiring for 230V bi directional curtain motors: Direction Movement Motor 1 Channel 1 Channel 5 Motor 2 Channel 2 Channel 6 Motor 3 Channel 3 Channel 7 Motor 4 Channel 4 Channel 8 DOWN Motor 1 NEUTRAL Direction...
-
Page 8: Hardware Controls
hardware controls AUX Input - This is a dry contact interface that is active low. The dry contact is connected between the AUX and GND terminals on the DyNet connector strip. The function of the AUX input is programmable. Ensure that the cable length between the dry contact and terminal strip is no longer than 2 metres. -
Page 9: Troubleshooting
Check the following list. If you are still unable to rectify the situation, contact your nearest Dynalite dealer. A complete list of distributors worldwide can be found on the Internet at: www.philips.com/dynalite Please ensure that you have completed the following prior to calling our technical support department. - Page 10 Dynalite Manufactured by WMGD Pty Ltd (ABN 33 097 246 921). All rights reserved. Dynalite, Dimtek, DyNet and DLight and associated logos are the registered trademarks of Dynalite Intelligent Light Pty Ltd. Not to be reproduced without permission. Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: +61 2 8338 9333 E-mail: dynalite.info@philips.com Web: Philips.com/dynalite...