Subscribe to Our Youtube Channel
Related Manuals for Clarke CCD30LIC
Summary of Contents for Clarke CCD30LIC
- Page 1 CCD30Lic - 18V Hammer Drill.fm Page 1 Wednesday, October 3, 2018 3:15 PM 18V HAMMER DRILL / DRIVER MODEL NO: CCD30LIC PART NO: 6479650 OPERATION & MAINTENANCE INSTRUCTIONS LS1018 - ISS 1 ORIGINAL INSTRUCTIONS...
-
Page 2: Carton Contents
CCD30Lic - 18V Hammer Drill.fm Page 2 Wednesday, October 3, 2018 3:15 PM INTRODUCTION Thank you for purchasing this CLARKE 18V Hammer Drill / Driver. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Safety Precautions
CCD30Lic - 18V Hammer Drill.fm Page 3 Wednesday, October 3, 2018 3:15 PM SAFETY PRECAUTIONS WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/ OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED BELOW REFERS TO YOUR 18V HAMMER DRILL / DRIVER. - Page 4 CCD30Lic - 18V Hammer Drill.fm Page 4 Wednesday, October 3, 2018 3:15 PM 4. POWER TOOL USE AND CARE a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate which it was designed.
-
Page 5: Environmental Protection
CCD30Lic - 18V Hammer Drill.fm Page 5 Wednesday, October 3, 2018 3:15 PM 6. SERVICE a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. -
Page 6: Battery Charging
CCD30Lic - 18V Hammer Drill.fm Page 6 Wednesday, October 3, 2018 3:15 PM BATTERY CHARGING WARNING: WHEN THE BATTERY IS REMOVED FROM THE DRILL AFTER USE, IT MAY BE HOT. ALWAYS ALLOW TO COOL BEFORE RECHARGING. DO NOT RECHARGE A HOT BATTERY. -
Page 7: Before Use
CCD30Lic - 18V Hammer Drill.fm Page 7 Wednesday, October 3, 2018 3:15 PM BEFORE USE FITTING THE BATTERY 1. Slide the battery pack onto the base of the handle until it ‘clicks’ into position. REMOVE THE BATTERY 1. Press and hold the release button on top of the battery. -
Page 8: Speed Range
CCD30Lic - 18V Hammer Drill.fm Page 8 Wednesday, October 3, 2018 3:15 PM ADJUSTMENTS FORWARD/REVERSE The forward/reverse switch is used to select the direction of rotation. 1. Use the forward/reverse switch to select the direction of rotation. 2. Reverse should only be selected when removing screws. -
Page 9: Selecting The Drilling Mode
CCD30Lic - 18V Hammer Drill.fm Page 9 Wednesday, October 3, 2018 3:15 PM SELECTING THE DRILLING MODE WARNING: DO NOT CHANGE THE DRILLING MODE WHILE THE CHUCK IS ROTATING. The drill is equipped with two drilling modes. Hammer drilling mode... -
Page 10: Torque Adjustment
CCD30Lic - 18V Hammer Drill.fm Page 10 Wednesday, October 3, 2018 3:15 PM TORQUE ADJUSTMENT To select the correct torque setting for screwdriving: 1. Set the Speed Range selector ring to 1. 2. Set the mode selector ring to 1. -
Page 11: Drilling Tips
CCD30Lic - 18V Hammer Drill.fm Page 11 Wednesday, October 3, 2018 3:15 PM DRILLING TIPS • Always use sharp, good quality drill bits. The performance of your drill is dependant on the quality of the bits used. • After drilling material to the full depth, do not simply pull out the drill but maintain chuck rotation to ease withdrawal. -
Page 12: Screwdriving Tips
CCD30Lic - 18V Hammer Drill.fm Page 12 Wednesday, October 3, 2018 3:15 PM SCREWDRIVING TIPS • Place the screwdriver bit in the head of the screw and apply light pressure to the drill. • If the screw head is not flush with the material, increase the torque and start again. -
Page 13: Specifications
CCD30Lic - 18V Hammer Drill.fm Page 13 Wednesday, October 3, 2018 3:15 PM SPECIFICATIONS Model Number CCD30LIC Part Number 6479650 Charger voltage 230V~50Hz Battery voltage 18 volts (2000 mAh) Charging time 1.67h Keyless chuck capacity 0.8 mm -10 mm Torque settings... -
Page 14: Declaration Of Conformity
CCD30Lic - 18V Hammer Drill.fm Page 14 Wednesday, October 3, 2018 3:15 PM DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 15 CCD30Lic - 18V Hammer Drill.fm Page 15 Wednesday, October 3, 2018 3:15 PM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 16 CCD30Lic - 18V Hammer Drill.fm Page 16 Wednesday, October 3, 2018 3:15 PM...
Need help?
Do you have a question about the CCD30LIC and is the answer not in the manual?
Questions and answers