Specifications - Simer 2925B Owner's Manual

Safety / General Information
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury.
warns about hazards that will cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which
are important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
DESCRIPTION
Simer laundry pump system, Model number 2925B-01, is
ideal for home wastewater removal from sinks and wet
bars and for drain water transfer from air conditioners or
dehumidifiers. The 3/10 HP submersible pump is
equipped with a 3-prong grounding-type power cord.
Motor is oil filled and sealed for cooler running. Upper
sleeve/lower ball bearings on motor shaft never need
lubrication. Automatic reset thermal protection.
NOTICE: This unit is not designed for applications involv-
ing salt water or brine! Use with salt water or brine will
void warranty.
ELECTRICAL & FLOAT SWITCH

SPECIFICATIONS

Motor
Motor Full Load
Series HP Amps
2925B-01 3/10 10.0
SPECIFICATIONS
Power Supply Required .............................115V, 60 HZ.
Liquid Temp. Range ...............32° F to 120° F (0°-49° C)
Individual Branch Circuit
Required (minimum) .........................................15 Amps
Discharge ...................................................1-1/4" MNPT
For parts or assistance, call Simer Customer Service at
*Switch Setting
in inches (mm)
On Off
7" (178) 2" (51)
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give many
years of trouble-free service when correctly installed,
maintained, and used. However, unusual circumstances
(interruption of power to the pump, dirt/debris in the
sump, flooding that exceeds the pump's capacity, electri-
cal or mechanical failure in the pump, etc.) may prevent
your pump from functioning normally. To prevent possi-
ble water damage due to flooding, consult your dealer
about installing a high water alarm. See the
"Troubleshooting Chart" in this manual for information
about common sump pump problems and remedies.
For more information, see your dealer or call customer
service at 1-800-468-7867 or 1-800-546-7867.
1. Know the pump application, limitations, and poten-
tial hazards.
2. Disconnect the power before servicing.
3. Release all the pressure within the system before ser-
vicing any component.
4. Drain all the water from system before servicing.
5. Secure the discharge line before starting the pump.
An unsecured discharge line will whip, possibly caus-
ing personal injury and/or property damage.
6. Check the hoses for a weak or worn condition before
each use, making certain that all connections are
secure.
7. Periodically inspect the system components. Keep
free of debris and foreign objects. Perform routine
maintenance as required.
8. Provide a means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep the work area clean, uncluttered and properly
lighted – replace all unused tools and equipment.
c. Keep visitors at a safe distance from the work area.
d. Make the workshop child-proof – with padlocks,
master switches, and by removing starter keys.
10. When wiring an electrically driven pump, follow all
electrical and safety codes that apply.
11. This equipment is only for use on 115 volt (single
phase) and is equipped with an approved 3-conduc-
tor cord and 3-prong, grounding-type plug.
To reduce risk of electric shock, pull
plug before servicing. This pump has not been inves-
tigated for use in swimming pool areas. Pump is sup-
plied with a grounding conductor and grounding-type
attachment plug. Be sure it is connected only to a
properly grounded grounding-type receptacle.
Where a 2-prong wall receptacle is encountered, it
must be replaced with a properly grounded 3-prong
receptacle installed in accordance with codes and
ordinances that apply.
12. All wiring should be performed by a qualified
electrician.
1-800-468-7867 / 1-800-546-7867
2