Zip HydroTap All-In-One 89650 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Zip Manuals
  4. Plumbing Product
  5. HydroTap All-In-One 89650
  6. Installation and operating instructions manual

Zip HydroTap All-In-One 89650 Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operating Instructions
®
Zip HydroTap All-In-One
Filtered Boiling and Chilled water plus Hot and Cold water for kitchens and tea rooms.
This Installation Instruction covers the following HydroTap commercial models:
Affix Model Number Label Here
89650
GP
HydroTap Installation and Operating Instructions 89650 - October 2012 v2.00
Page 1 of 20

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HydroTap All-In-One 89650 and is the answer not in the manual?

Questions and answers

Related Manuals for Zip HydroTap All-In-One 89650

Summary of Contents for Zip HydroTap All-In-One 89650

  • Page 1 Installation and Operating Instructions ® Zip HydroTap All-In-One Filtered Boiling and Chilled water plus Hot and Cold water for kitchens and tea rooms. This Installation Instruction covers the following HydroTap commercial models: Affix Model Number Label Here 89650 HydroTap Installation and Operating Instructions 89650 - October 2012 v2.00...

  • Page 2: Table Of Contents

    Contents Read these warnings first ......3 Models covered by these instructions ....4 Installation requirements .

  • Page 3: Read These Warnings First

    Read these warnings first Safety This appliance is not intended for use by persons (Including Children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance Refrigerant The HydroTap Chilling unit contains 134A refrigerant under pressure.

  • Page 4: Models Covered By These Instructions

    Read these warnings continued Frost Protection If this appliance is located where the ambient air temperature could fall below 5ºC when the heater is not in use, do not turn off the appliance electrically. This safeguard does not offer the same protection to the connecting pipework and fittings.

  • Page 5: Special Tools Required

    Installation requirements continued • Power supply 220-240 Volt AC, for connection to the heater via a 10 amp (160/125) or 15 amp (240/175) GPO. • This switch must provide all-pole disconnection and a contact separation of at least 3mm installed in accordance with wiring rules.
  • Page 6 Installation procedure continued Step B - Installing the undersink unit NOTE : SPECIAL NOTE: The HydroTap undersink units are heavy, take note of the New hose sets supplied with the weights listed in the table on page 4. If you think you cannot lift the unit unit should be used.
  • Page 7 Installation procedure continued the USB plug carefully and connect, do not force the plug. Once connected, fix the cable to the wall, ensure it is away from any possible water splashes and is off the floor. Vent line Hot line Chilled line Model: NON Vented.
  • Page 8 HydroTap BC range. Product range descriptions could be one of the following: BO1.30E11O CP1.30E11O BF1.30E11O BC1.30E110 Zip Industries HTAP BC 1.30E11O BA1.30E11O CO1.30E11O BC CORR3 BF CORR3 Fig.1 2. The screen will then display “To Select Model Press ADJUST->“ as shown in Fig.2.

  • Page 9: Operating The Mixer Tap

    Operating the mixer tap calibration mode. Press adjust to start calibration. The element will now Boiling Water Lever Chilled Water Lever cycle ON and heat the water to 95ºC maintaining it at that temperature for a short stabilization period. Once stabilized, the element will cycle ON, bring the water to boiling point and hold it there for a short period.

  • Page 10: Mains Version Connections (Diagrams)

    161.50 SILICONE HOSE FROM STEAM VENT IN HYDROTAP UNIT TO TAP VENT OUTLET POSITION NOTE: IF THE FLOW RATE IS TOO FAST, CUT THE RED SILICONE BOILING TUBE 75mm MINIMUM FROM THE CHILLED WATER BOTTOM OF THE BASE OF THE 240V GPO WATER ALL-IN-ONE TAP.
  • Page 11 ALL IN ONE TAP-MAINS VERSION SILICONE HOSE FROM BOILING WATER TANK IN HYDROTAP UNIT TO TAP BRAIDED HOSE BH1 FROM MAINS SUPPLY BENCHTOP CABINET DOOR 4mm BUFFER PAD TO ENSURE VENTILATION GAP BRAIDED HOSE BH2 FROM DOMESTIC HOT WATER SUPPLY SILICONE HOSE FROM CHILLED WATER TANK IN HYDROTAP UNIT TO TAP...

  • Page 12: Vented Version Connections (Diagrams)

    SILICONE HOSE FROM BOILING WATER TANK IN HYDROTAP UNIT TO SILICONE HOSE FROM STEAM BRAIDED HOSE BH1 VENT IN FROM MAINS HYDROTAP WATER SUPPLY TO TAP SILICONE HOSE FROM CHILLED BRAIDED HOSE BH2 WATER TANK IN FROM ALL-IN-ONE TAP HYDROTAP UNIT TO VENTURI TO TAP BRAIDED HOSE BH3...
  • Page 13 ALL IN ONE TAP-VENTED VERSION MAINS AMBIENT WATER SUPPLY (ISOLATION VALVE NOT SUPPLIED)

  • Page 14: Operating The Hydrotap

    Operating the HydroTap Blue Chilled Water Light On all the time: Press or pull lever This indicates that the temperature of the chilled water is within the usable temperature range. Flashing slowly : This indicates that the chilled water is not at the right temperature. Wait up to 20 minutes.

  • Page 15: Replacing The Filter

    Replacing the Filter The Zip HydroTap notifies when filter replacement is due. The default setting is 6000 Ltrs, but this can be set in increments of 1000Ltr from 1000Ltr to 10000Ltrs. When a filter change is due, the Change Filter light will flash white once a minute and remain so until reset.

  • Page 16: Setting The Energy Saver Timer

    Setting the Energy Saver Timer Plus Adjust Button Mode Plus Button Minus Adjust Button Mode Minus Button Note: Mode buttons change the screen options Adjust buttons select the screen options Normal Operation (not available on HT boiling only series) Set Time To change time, press either Mode or Mode button until Set Time is on...
  • Page 17 Setting the Energy Saver Timer (continued) Mode or Mode button until “Sleep Mode” is displayed. Press Adjust once to select Option 1: Sleep to 64ºC after 2 hours of NO USE Press Adjust once to select Option 2: Auto OFF after 2 Hrs of NO USE. When the period of inactivity passes, the display will show “Sleep Mode”.

  • Page 18: Auxiliary Fan Attachment

    Auxiliary fan attachment The HydroTap is equipped with an auxiliary fan connection point on the rear panel close to the cold water inlet / flex and plug area. The fan kit is available as a spare part. The fan operates in parallel with the Condenser fan helping to remove heat Auxiliary fan from the cupboard space.

  • Page 19: Cleaning

    Cleaning Do not use strong, corrosive, spray or abrasive cleaners. Clean with a soft cloth or brush and mild soap and water. Do not spray water over the tap as it may damage the low-voltage electronics. Undersink units must never be located near, or cleaned with water jets. Trouble shooting Symptom Possible Cause...

  • Page 20: Contact Details

    The standard cup referred to in this publication is 167 ml (6 fl oz). The standard glass is 200 ml (7 fl oz). The terms “Zip” and “HydroTap” are registered trade marks of Zip Heaters (Aust) Pty Ltd. Zip products described in this publication are manufactured under one or more of the following patents: AU675601, AU637412, AU635979, GB0422305, GB2065848, US4354049, US5103859, and US5099825.

Table of Contents