FAAC 596MPS Manual page 9

ENGLISH
3. WIRING DESCRIPTION
3.1. TERMINAL BOARD J1 (low volta ge)
1 = OPEN comma nd (N.O.)
Any d evic e (p ush-b utton, d etec tor,...) w hic h, b y c losing a
c onta c t, sup p lies a n op ening or c losing p ulse to the a uto-
ma tic system.
T o insta ll seve ra l Op e n d evic e s, c o nne c t N.O. c o nta c ts in
p a ra llel.
2 = FSW Closing sa fety devices conta ct (N.C.)
Sa fety d evic es a re a ll d evic es (p hotoc ells, sensitive ed g es,
ma g netic c oils) with N.C. c onta c t, whic h op era te if there is
a n o b sta c le in the a re a the y p ro te c t.
Sa fe ty d evic e s p ro te c t the a re a a ffe c te d b y the c lo sing
m ovem ent of the a utom a tic system .
If the sa fety d evic es a re trip p ed d uring c losure, a utoma tic
m ovem ent is reversed , w herea s they ha s no effec t d uring
o p e ning . The sa fe ty d e vic e s o p e ra ting w he n the a uto -
m a tic system is op en or p a using , p revent c losure.
T o insta ll severa l sa fety d evic es, c onnec t the N.C. c onta c ts
in series.
ÜIf no c lo sing sa fety d evic es a re insta lled , fit a jum p er o n
this inp ut:
• w ith term ina l 4 (if fa ilsa fe is d isa b led ), o r
• w ith term ina l 6 (if fa ilsa fe is ena b led ).
3 = STOP comma nd (N.C.)
This is a ny d evic e (e.g . a p ush-b utto n) w hic h, b y o p ening
a c o nta c t, sto p s m o vem ent o f the a uto m a tic system .
T o insta ll seve ra l sto p d evic e s, c o nne c t the N.C. c o nta c ts
in series.
ÜIf Sto p d evic es a re no t c o nne c te d , link the inp ut to the
c o m m o n c o nta c t (term ina l 4) via a jum p er.
4 = C o m m o n fo r c o nta c ts/ Ne g a tive fo r a c c e sso rie s
supply (-)
5 = Positive for 24 Vdc a ccessories supply (+)
Ma x loa d of a c c essories: 250 m A.
T o c a lc ula te a b sorp tion va lues, refer to the instruc tio ns for
ind ivid ua l a c c essories.
6 = Fa ilsa fe (-) (see " 4. Progra mming ")
If Fa ilsa fe is ena b led , you must c onnec t the neg a tive p oles
of the p hotoc ells p rojec tors to this term ina l.
7 = FCC Closing limit-switch conta ct (N.O.)
The c lo sing lim it-sw itc h is a d e vic e w ith a N.O. c o nta c t
w hic h, b y b e ing trip p e d w he n the a uto m a tic syste m
rea c hes the c losed p osition (c losing the c onta c t), c a uses
the a uto m a tic syste m to sto p a fte r a b o ut 1 se c o nd .
8 = C o m m o n fo r c o nta c ts/ Ne g a tive fo r a c c e sso rie s
supply (-)
9 = FCA Closing limit-switch conta ct (N.O.)
The o p e ning lim it-sw itc h is a d e vic e w ith a N.O. c o nta c t
w hic h, b y b e ing trip p e d w he n the a uto m a tic syste m
re a c he s the o p e n p o sitio n (c lo sing the c o nta c t), c a use s
the a uto m a tic syste m to sto p .
3.2. TERMINAL BOARD J2 (high volta ge)
10-11 = Connection to initia l thrust ca pa citor
If the a p p lic a tion ha s tw o op era tors, c onnec t the c a p a c i-
to rs in p a ra llel.
12 – 13- 14 = Connection to electric motor
T erm ina ls 12-13 should b e c onnec ted to the motor p ha ses
(b ro w n a nd b la c k c a b les) w herea s term ina l 14 sho uld b e
c o nnec ted to the m o to r (b lue c a b le).
If the a p p lic a tio n ha s tw o o p e ra to rs, c o nne c t the tw o
m otors in p a ra llel.
15-16 = Timed courtesy light (596MPS)
Fla shlight (610MPS)
The func tion of this outp ut d iffers a c c ord ing to c a rd mod el:
• 596MPS:
Co nne c t the c o urte sy lig ht - 230V~ 60W ma x. - if a ny. The
c ourtesy lig ht is a c tiva ted w hen the m otor sta rts a nd sta ys
lig hted fo r a b o ut 90 sec o nd s a fter end o f m o vem ent.
• 610MPS:
Co nne c t the fla shlig ht - 230V~ 60W m a x.
3.3. CONNECTOR J3 (low volta ge)
Connec tor J3 is used for ra p id c onnec tion of MINIDEC, DECODER,
a nd RP RECEIVER c a rd s (Fig . 4,5,6)
Insta ll b y fitting the a c c essory c a rd s so tha t their c omp onents sid e
fa c es the insid e of the elec tronic a p p lia nc e.
Insert a nd rem ove the c a rd s a fter c utting p ow er.
Fig.4
PLUS
844MPS
844MPS
MINIDEC
SL/DS
3.4. CONNECTOR J4 (low volta ge)
T he J4 c onnec tor is used for ra p id c onnec tion of the op ening p ush-
b utton on the up -a nd -over op era tors' housing .
3.5. TERMINAL BOARD J9 (high volta ge)
Term ina l b oa rd for c onnec ting 230V~ 50Hz p ow er sup p ly.
[L=Line - N=Neutra l - W= Ground ].
4 . PRO G RAM M ING
To p rog ra m m e op era tion of the a utom a tic system , turn the
mic roswitc hes a s follows:
Logic SW1 Pa use time (se c .)
E O FF
A O N
ON
OFF 1 2 3 4
Be ha viour FSW
o p e ns im m e d ia te ly
o p e ns w he n d ise ng a g e d
ON
OFF 1 2 3 4
Op/ Clos. time SW4 SW5
(se c .)
4 O FF O FF
5 O N O FF
7 O FF O N
9 O N O N
7
Fig. 5 Fig. 6
844MPS
DECODER
SL/SLP/DS
596MPS
SW5 Fa ilsa fe
30 O FF
60 O N
5 6
Op/ Clos. time (se c .)
40
SW2 35
O FF 30
ON 25
610MPS
Logic Pa use SW1
(se c .)
E / O FF
0 O N
2 O FF
5 6
5 O N
A 10 O FF
15 O N
30 O FF
60 O N
Fa ilsa fe
No
Yes
ENGLISH
SW6
No O FF
Yes O N
SW3 SW4
O FF O FF
O N O FF
O FF O N
O N O N
SW2 SW3
O FF O FF
O FF O FF
O N O FF
O N O FF
O FF O N
O FF O N
O N O N
O N O N
SW6
O FF
O N