Fema Electronica S Series User Manual
Hide thumbs
Also See for S Series:
- User manual (20 pages) ,
- User manual (20 pages) ,
- User manual (37 pages)
Table of Contents
Advertisement
Quick Links
Series S
Panel Meters
Model S40-R
Panel meter for ratiometric and potentiometer signals. Accepts 3 wire ratiometric signals.
Accepts potentiometers up to 5 MOhm and from 200 Ohm. Reduced size 72x36mm.
Reading with 4 digits. 5Vdc transducer excitation. Segment linearization, maximum
and minimum display memory, scalable reading, filters, steps, signal autocorrection,
"measure" function, peak&hold, alarms with double setpoints, 5 levels of brightness, ...
Universal AC and DC power modules and up to 2 modules for signal retransmission and
control (relay outputs, analogue outputs, ...).
USER'S MANUAL
(2704R02)
Panel meter 72x36mm
for Ratiometric signals
Potentiometers up to 5M
Advertisement
Table of Contents
Related Manuals for Fema Electronica S Series
Summary of Contents for Fema Electronica S Series
- Page 1 Series S Panel Meters Panel meter 72x36mm Model S40-R for Ratiometric signals Potentiometers up to 5M Panel meter for ratiometric and potentiometer signals. Accepts 3 wire ratiometric signals. Accepts potentiometers up to 5 MOhm and from 200 Ohm. Reduced size 72x36mm. Reading with 4 digits.
-
Page 2: Table Of Contents
User’s Manual S40-R 1. Meter S40-R Panel meter 72x36mm for ratiometric and potentiometer signals Panel meter for ratiometric and potentiometer signals, from 3 signal to the low or high reading), “peak&hold” function and wire transducers. The meter provides +5V (max. 35mA) and password. -
Page 3: Front View
User’s Manual S40-R 1.2 Front View 1.5 Input signal connections Alarms 1 2 3 Vexc +5V Ratiometric or potenti- ometer 3 wire transducer Signal Logo Units Common Button LE Button UP Button SQ Access to Access to “Information Menu” “Configuration Menu” 1.3 Rear View Option1 Option2... -
Page 4: Technical Data
User’s Manual S40-R 1.6 Technical data 1.6 Technical data (cont.) Digits Peak & Hold Type 7 segments, red Double setpoints Height 14 mm Brightness control yes, 5 levels Display maximum 9999 Display minimum -1999 Thermal stability Decimal point selectable 8.8.8.8. offset 10 ppm/ºC Overrange... -
Page 5: Operating The Menus
User’s Manual S40-R 1.8 Operating the menus 1.9 Default factory configuration The instrument has two menus accessible to the user : Range and scaling Pot.<5K Scaling 0/99.99%=0/99.99% “Configuration Menu” (key SQ) Alarms 1,2 and 3 “Information Menu” (key UP) Active Off (not managed) Type maximum... -
Page 6: Configuration Menu
User’s Manual S40-R 1.10 Configuration menu Press SQ button to enter Configuration Menu See menu for Alarm1 Ratiometric signal Input Potentiometer <5K Potentiometer <5M Value in KOhm Display Scaling Input Low Fixed Digits Fix digits Display Low Input High Average Display High Press LE to change selection Steps... -
Page 7: Configuration Menu (Cont.)
User’s Manual S40-R 1.10 Configuration menu (cont.) Tools Advanced Points Input0 Display0 display (Segment linearization) Display10 Input10 Enter signal values (“Input”) and associated display val- ues (“Display“) for each linearization point. Then activate “Act” to “On”. In case of error verify the points data. Activate Reset Password... -
Page 8: Input Menu
User’s Manual S40-R Hysteresis (HYST) - Value from “0” to “9999”. Points of hyster- 1.10.1 Input menu esis. The hysteresis applies on the deactivation of the alarm. The “input” menu selects the input signal range. Options are : Delay (DEL) - Value from “0.0” to “99.9” seconds. Delay to be applied to the relay activation and deactivation. -
Page 9: Tools
User’s Manual S40-R Peak & Hold (P.HLD) - Peak & Hold function detects sharp 1.11 Messages and errors drops in the displayed value, and holds the display if a display drop is detected. To disable the hold function for a moment, When the instrument detects that the displayed value does press any of the front buttons or wait for a predefined time : not correspond to the expected value, the display will flash... -
Page 10: Information Menu
User’s Manual S40-R 1.12 Information menu 1.12.1 Information menu Configuration (Conf) - Informs the configured input signal Press UP button to enter Information Menu range (4/20mA, 0/10Vdc, ...), and the values for input low “ILo”, display low “dLo”, input high “IhI” and display high “dhI”. Range (Rat.,Pot<5K, Pot<5M) Configuration Maximum (MAX) - Value of the maximum display. -
Page 11: Warranty
User’s Manual S40-R 1.14 Warranty 1.16 CE declaration of conformity All instruments are warranted against all manufacturing Manufacturer FEMA ELECTRÓNICA, S.A. Altimira 14 - Pol. Ind. Santiga defects for a period of 24 MONTHS from the shipment date. E08210 - Barberà del Vallès This warranty does not apply in case of misuse, accident or BARCELONA - SPAIN manipulation by non-authorized personnel. -
Page 12: Output And Control Modules
Module with 1 analogue output. Configurable 4/20mA or Module with 1 relay. Up to a maximum of two R1 modules can be installed in one S Series panel meter. For more relay 0/10Vdc. Output signal proportional to the reading. Scaling through the frontal keypad. -
Page 13: Modules R2, R4
Only one special Opt 1 Opt 2 module R2 or R4 can be installed in an S Series panel me- ter. Special modules R2 and R4 are not compatible with R1 A B C D E F G H I J K L modules. - Page 14 User’s Manual S40-R FEMA ELECTRÓNICA - Page 14...
- Page 15 User’s Manual S40-R FEMA ELECTRÓNICA - Page 15...
- Page 16 other products Panel Meters Panel Meters Panel Meters Standard 96x48mm Small 72x36mm Miniature 48x24mm Large Displays Signal Converters Bar Meters 60&100mm digit & Isolators www.fema.es ELECTRONIC INSTRUMENTATION FOR INDUSTRY FEMA ELECTRÓNICA, S.A. Altimira 14 - Pol. Ind. Santiga E08210 Barberà del Vallès BARCELONA - SPAIN Tel.