Page 2
Technical publication for informative purposes, edited by FERMAX ELECTRÓNICA S.A.E. FERMAX ELECTRÓNICA S.A.E., in a policy of ongoing improvement, reserves the right to modify the contents of this document and the features of the products cited herein at any time and with no prior notice.
DETECTA-6 DETECTA-6 INDEX INTRODUCTION ....................5 MONITOR-TELEPHONE DESCRIPTION ............7 Video Entry Commands ............... 8 Alarm Centre Commands............. 9 Keypad/Status LEDs ..................... 9 Zones LEDs ......................9 Keypad Display ..................... 10 VIDEO ENTRY OPERATION ................11 Call ....................12 Answer Call ................. 12 Open Door to Visitor ..............
Page 4
DETECTA-6 DETECTA-6 BASIC USER PROGRAMMING ............... 25 Enter/Exit Programming .............. 27 Programming Parameters ............27 Programming Date and Time ..........Programming User Codes ................28 Cancel User Codes ..................29 Change User Codes ..................29 Programming Telephones for alarm alerts ............. 30 ADVANCED USER PROGRAMMING ..............
Page 6
This Certificate also ensures that the Equipment may be installed in an Alarm Reception Centre, either after installation or at any time afterwards. Fermax places the Approved Security Services Network at your service, which you may consult through our website: www.fermax.com.
DETECTA-6 DETECTA-6 DETECTA 6 MONITOR-TELEPHONE DESCRIPTION F E R M A X Detecta 6 Monitor Detecta 6 Telephone ADS, 4+N and MDS System ADS System Video entry system commands description Monitor and Telephone: DOOR RELEASE / Guard Unit call button.
DETECTA-6 DETECTA-6 Alarm centre commands description The alarm centre is managed (alarm arming/disarming, F E R M A X alarm options...) through the monitor/telephone keypad, introducing the corresponding code in each case (the arming/disarming codes and centre operation are explained in the following chapters).
The zone LEDs show the zones that have set off the alarm. User nº: The Detecta-6 alarm centre has up to 8 user codes, numbered from 1 to 8, that enable connection/ disconnection of the alarms, with certain specific features (see User Codes chapter).
DETECTA-6 DETECTA-6 ALARM OPERATION Connecting/disconnecting the centre (Arming/Disarming) * Connecting the centre: - When the alarm is connected, the centre initiates the Exit route, giving off an acoustic alert during the time available - Option 1 to leave the home after making the connection.
DETECTA-6 DETECTA-6 Partial Omission User code Nº of Zones Lets the user select the zones that will not be connected (they are omitted) when Partial Connection is set. Introduce a valid user code, then press the [A] key for 2 seconds, followed by the numbers of the zones to...
DETECTA-6 DETECTA-6 Fast Key Functions When a key is pressed for 2 seconds, the function corresponding to the key pressed is implemented: Voice Mail : Voice mail is only recorded if there is a microphone connected to the centre. Detection Zones: The zone LEDs shows the zones that are currently detecting.
MEDICAL Alarm, sends the Medical alert to the Alarm Reception Centre. Setting off an alarm When the Detecta-6 centre is armed, and a detection takes place, the centre acts as follows: - The telephone/monitor generates an acoustic alert (siren mode).
DETECTA-6 DETECTA-6 Events Check (Alarm Memory) When an alarm is set off, the Detecta-6 centre memorises the event so that you can check up on it later. The existence of alarm events is indicated by means of the LED lighting up.
DETECTA-6 DETECTA-6 TELECONTROLLER Remote control is the system whereby alarm centre functions can be controlled through the telephone (landline or mobile). To manage the centre by telephone, it is necessary to: 1. Enter telecontroller mode There are two ways to enter telecontrol: - When an alarm goes off: the centre calls the user.
DETECTA-6 DETECTA-6 2. Telecontrol Commands Commands introduced by the user via telephone, once the telecontrol mode is activated, enabling certain operations on the centre. If the code entered is correct, the centre reprodu- Connect / Disconnect User the centre ces the «Connected or Disconnected» message,...
Page 22
Error / Fault Message There is an Error or Fault in the system The default header message is: «Detecta-6 Alarm Centre» and must be previously enabled by the installer. It is possible to personalise voice messages. See the «Message Recording» option in the Programming Manual.
DETECTA-6 ADVANCED USER FUNCTIONS Control of devices connected to the centre Using the Detecta-6 monitor keypad, it is possible to activate/deactivate devices (lights, blinds, irrigation...) connected to the alarm centre. Check with your installer if you have control devices installed.
DETECTA-6 DETECTA-6 PROGRAMMING (Codes-Telephones-Date and Time) Pag 25...
Page 26
DETECTA-6 DETECTA-6 USER PROGRAMMING With the telephone/monitor keypad, the user can program certain parameters of the cen- tre, such as: centre date and time, user codes and private telephone numbers for alerts. To program codes, telephones, etc, you must: 1. Enter programming mode.
DETECTA-6 DETECTA-6 1. Enter Programming Mode * Enter Programmong mode: Master User Code JK L Master Code= user Code 1 WXYZ (By defaulto: 1111) 2 sec. When you enter user programming, on the monitor display you can see: You cannot enter programming mode if the centre is connected.
DETECTA-6 DETECTA-6 * Programming User Codes Up to 8 user codes can be programmed, letting you connect/disconnect the centre (with some exceptions) To program the different user codes, enter programming and proceed as follows: 1. Introduce the address of the code to be programmed.
DETECTA-6 DETECTA-6 * Cancel a User Code: To cancel a user code when in programming, proceed as follows: 1. Introduce the address of the code to be cancelled. 2. Then press the [*] and [5] keys consecutively. 3. Validate by pressing the [#] key.
DETECTA-6 DETECTA-6 Programming (Private) Telephones for alarm alerts In order to receive alerts from the centre on your telephone (mobile or landline), at least one telephone number must be programmed to be called in the event of any incidents. To program or change a telephone number when in programming, take the following steps: 1.
ADVANCED USER PROGRAMMING Device Scheduler The Detecta-6 system has a scheduler (relay programs) with which you can configure up to 8 schedules, with two device activation/deactivation intervals. These Schedules are configured by the Installer. Check with your installer to see if there are any «relay programs - Schedule Planner».
DETECTA-6 DETECTA-6 FAST GUIDE TO FUNCTIONS Pag 33...
Page 34
DETECTA-6 DETECTA-6 FAST GUIDE TO FUNCTIONS CONNECT/DISCONNECT CENTRE KEY SEQUENCE EXAMPLE User code + [#] 1111# Connect/Disconnect centre [*] [#] Fast Connection 2 sec Absolute Connection User code + [A] + [#] 1111A# Absolute Disconnection User code + [B] + [#]...
Page 35
DETECTA-6 DETECTA-6 TELECONTROLLER KEY SEQUENCE Initiate Telecontrol. Centre calls User. [*] + [5] User code + [#] Initiate Telecontrol. User calls Centre. Connect / Disconect Centre User code + [#] Cut off Communication [*] + [0] + [0] Activate/Deactivate Devices...