Operation - Viking K-1775-BN-IP Product Manual

42. Unit Firmware
If new K-1775-IP firmware is available, after opening the programming software a pop window will come up asking you
if you would like to update firmware. An alternative method of updating can be done by clicking the Unit firmware
"Update Unit" button. You can then browse to the folder that contains the HEX file for updating the unit's firmware. This
method is typically only used when Viking Technical Support has sent you updated firmware.
43. Import/Export
The Import/Export feature is useful for backing up all the K-1775-IP's programming or for importing programming when
installing multiple units with a majority of the same programming.
44. Clear Unit Settings
Clicking on the "Clear Unit settings" button in programming will reset all of the Programming Features back to their
factory default settings. Note: This command will not change or reset your IP settings.
45. Clear IP Settings
Clicking on the "Clear IP Settings" will reset all of the IP settings back to their factory default settings. This also clears
paging Group settings and Addresses. Note: This will not effect any speaker or paging settings.
46. Diagnostics
The Diagnostics section in the Viking IP Programming can be used to test the functionality of the two relays, read
current relay status, perform mic/spkr diagnostics, or to display information on the last card or fob detected by the card
reader.
47. REX Input
The K-1775-IP has one Request for Exit (REX) trigger input. The REX switch must have a momentary, normally open
contact. When the K-1775-IP detects a contact closure on the REX trigger input it performs one of the following actions,
based on the Relay Mode settings (see section 17):
Relay 1 "Door Strike", relay 2 other: Relay 1 will be activated for the programmed Relay 1 Activation Time.
Relay 1 other, relay 2 "Door Strike": Relay 2 will be activated for the programmed Relay 2 Activation Time.
Relay 1 "Door Strike", relay 2 "Door Strike": If the Relay Activation Delay is disabled, Relay 2 will be activated for
the programmed Relay 2 Activation Time. If Relay Activation Delay is not disabled, Relay 2 will be activated for the
programmed Relay 2 Activation Time, then after the Relay Activation Delay time has passed, Relay 1 will be activated
for the programmed Relay 1 Activation Time. This is useful in two door vestibule applications where Relay 1 is used to
unlock the outside door, and Relay 2 is used to unlock the inside door. Note: For security reasons this input is disabled
when the relay is set to "External".
A. "CALL" Button
With the Call Button Delay set to No Delay, when the "CALL" button is pressed, the K-1775-IP immediately dials the pre-
programmed telephone number stored in the Phone Number Database Index location 0. With the call button Auto Dial Delay
set from 1 - 20, when the "CALL" button is pressed you will hear 1 - 20 seconds of dial tone, allowing you time to enter the
1-3 digit Speed Dial number or keyless code. The unit will then dial the Phone Number Database Index location 0-250
associated with the preprogrammed 1-3 digit Speed Dial Number (0-999). The Call Status LED momentarily flashes during
dialing. In the event the line is busy or there is a ring-no-answer, the unit can be programmed to call a second roll over
number.
When the call is answered, relay activation commands can be entered or the # key can be used to force the phone to hang-up.
After communication is established, enter the 1 or 2 digit relay activation command (factory set to ",,"
) to momentarily activate the entry phone (door strike) relay. Two beeps will be heard confirming that the relay has
for Relay 2
been activated. If you require the relay to remain on continuously (ie: a truck delivery), enter Touch Tones "11" or "21" to
continuously activate relay 1 or relay 2 respectively. A double beep will indicate that the relay is latched on. When the visitor
calls in again (ie: they are finished unloading the truck), enter Touch Tones "10" or "20" to deactivate relay 1 or relay 2
respectively. A single beep will indicate the relay is latched off.

Operation

22
for Relay 1 and ",2"