Table of Contents
Advertisement
Options (cont'd)
10-90282 KIT: ELECTRIC ACTUATOR
An installation video and set up guide as well as troubleshooting videos can be found on the support page at abisupport.com:
https://www.abiattachments.com/wp-content/uploads/2019/06/Actuator-Setup-Guide2-2013.pdf
https://www.abiattachments.com/guides/rascal-product-manual/#section-3
https://www.youtube.com/watch?v=SEhCApqXQIY
https://www.youtube.com/watch?v=j2K_guT1zo8
NOTE: TO AVOID ELECTRICAL DAMAGE TO THE UNIT BY SPLICING THE RASCAL WIRE HARNESS INTO THE TOW
VEHICLE WIRING SYSTEM AND POSSIBLY REVERSING THE WIRES, OR THE TOW VEHICLE HAVING A POSITIVE GROUND
RELAY SYSTEM, CONNECT THE WIRING HARNESS DIRECTLY TO THE TOW VEHICLE BATTERY (BLACK TO GROUND AND
RED TO POSITIVE).
ABI-WCK2 WIRELESS REMOTE
W/2 KEY FOBS
If 10-90282 Electric Actuator Kit is ordered, the
wireless remote can also be ordered to run the
actuator remotely. Open the Black Box from 10-
90282 kit. (Fig 32).
NOTE: Black box does NOT need
to be removed from Rascal to install the wireless
system - black box in views is only removed for
installation demonstration.
Locate the preinstalled 4 pole connector inside the
Black Box, which has yellow, green, black, and
white wires connected to it (Fig 33).
Visit: www.abisupport.com
The optional electric actuator kit replaces the
manual square hand jack to raise and lower the
wheel system on the Rascal. This allows the ability
to raise and the unit from the seat of the tow vehicle
using a switch secured to the handlebars.
Connect the Wireless Receiver plug to the 4 pole
connector in the Black Box. Plug will only fit one
way. Push the connectors together until it clicks
(Fig 34).
Carefully place the new Wireless Receiver in the
black plastic box. Close black box (Fig 35).
Press the buttons on the key fob to raise and lower
the Rascal wheels.
Preinstalled 4 pole connector
inside the Black Box.
Fig 32.
Fig 33.
28
Gently place the new Wireless Receiver
in the black plastic box.
Fig 34.
Fig 35.
Plug the connectors
together until it clicks.
KIT: MINI BOX BLADE W/SERRATED
BLADE
The Mini Box Blade w/Serrated Blade kit attaches to the
Finish Rake and is used to brake up and move material as
well as loosen rocks. It helps level out high and low spots.
To attach the Mini Box Blade assembly to the Rascal,
Unscrew and remove the two wing nuts and remove the two
T-clamp plates (Fig 36).
Slide the Mini Box Blade assembly under the Finish rake so
that the bolts the wing nut threads onto is in the second
comb slot from the end of the comb (Fig 37 and 38).
Lower the unit onto the Mini Box Blade assembly by
cranking the front wheel jack counterclockwise (Fig 39).
Replace T-Clamp plates and tighten wing nuts back onto
both bolts (Fig 40).
Use the closed end of a box wrench large enough to fit over
one wing of the wing nut to use as leverage to tighten the
wing nut tighter (Fig 41).
The unit is now ready to use as a mini box blade. The End
plates (Fig 42) will keep the material within the blade area to
help move the material from high spots and fill in low spots.
Remove wing nut
and T-Clamp plate
from both ends.
Fig 36.
Email: support@abiattachments.com
Fig 37.
Slide Mini Box Blade
assembly under Finish
Rake so that the bolts
that T-Clamp plate and
wing nut go onto slides
in second slot form
comb end on both ends.
Fig 38.
Crank wheel jack
counterclockwise
to lower finish rake
onto Mini Box Blade
assembly.
Fig 39.
Replace T-Clamp plates
and tighten wing nuts
back onto both bolts.
Fig 40.
Use the closed end
of a box wrench large
enough to fit over one
wing of the wing nut
to use as leverage to
tighten the wing nut
tighter.
Fig 41.
The End plates keep
the material within
the blade area to help
move the material
from high spots and
fill in low spots.
Fig 42.
Call Toll Free: 877-788-7253
29
Advertisement
Table of Contents
