Initial Configuration; Description Of Stove; Control Keyboard - Jøtul PF 710 Installation, Operation And Maintenance Manual

ENGLISH
After reaching the set temperature, the thermostat
opens the circuit and shuts down the stove.
The external thermostat must be connected to two
terminals found on the electronic card, which were
previously connected at the factory. Disconnect both
terminals and connect the two contacts of the thermostat
to them. It is important to set the stove to configuration
2, proceeding according to the instructions given in the
"Initial configuration" section.
After installation of the chronothermostat, the first
firing of the stove must be performed manually, when
the chronothermostat is in "call" mode� Proceed in the
same manner after power failure as well as after manual
shutdown of the stove�
To prevent the thermostat's operation from interfering with
the time intervals of the stove's work, it is recommended
to deactivate (set to OFF) the stove's time breaker switch
(see section 10�1)�
6�3 INITIAL CONFIGURATION
Depending on the type of installation, the stove must be
properly configured in order to optimise its operation.
For this purpose, the stove's power supply must be
activated first by pressing the switch found on the rear.
a) Using the arrow keys,
and press ;
b) Select the item using button
"7"
button ;
c) Select submenu
[30]
start to flash.
d) Press button and input "54" using buttons
e) Press button , to confirm.
f) The current configuration is displayed.
g) To change the configuration, press button
the number corresponding to the new configuration using
buttons .
h) Press button , to confirm.
After changing the configuration, an alarm message may
appear for several seconds� It should be ignored, and the
stove should be shut down by pressing the button found
on the rear� Wait several seconds, then fire it up again�
two dIffErEnt confIgUratIons
can bE ProgrammEd:
CONFIGURATION 1 (default)
This configuration is also suitable for firing up and
extinguishing the stove manually or in a programmed
manner. The stove modulates its power depending on
the ambient temperature read by the sensor found in the
stove.
The "Eco Mode" function can be activated so that the
stove extinguishes itself after reaching a set temperatu-
re and fires up again after the temperature in the room
drops�
In this configuration, it is also possible to select the anti-
freeze function.
CONFIGURATION 2
Set this configuration when the stove is controlled by an
external thermostat (or chronothermostat).
In this configuration, the stove will shut down after the
external thermostat activates following reaching of the
programmed temperature�
In this configuration, it is not possible to select the anti-
freeze function
10
select the Configuration menu
and confirm by pressing
using buttons ;
" --0"
, and input

7 DESCRIPTION OF STOVE

7�1 CONTROL KEYBOARD
Layout of control keyboard:
D
C
A) top part with status indicator LEDs and backlit icons
identifying individual functions,
B) LED display,
C) ignition button
D) "Cancel" button and "Alarm" display
E) two arrow keys for navigation in different menus
F) two buttons,
modification of working parameters,
G) send button
will
selection.
Due to the fact that this is a touch keyboard, it is enough
;
to press the buttons in order to activate them�
7�1�1 Status indicator LEDs
ICON
Pellet running out
Maintenance
Support
Remote control
receiver
Time breaker
switch engaged
Status indicator
LED (next to but-
ton
A
B
E
,
,
and , for access to submenus and
for confirmation of a parameter or
MESSAGE DESCRIPTION
This indicates that the pellet
container must be filled.
Signals that maintenance
must be carried out.
Signals activation of an alarm.
Receives commands from
the remote control pilot
(optional).
Signals activation of the time
breaker switch function.
LED is lit up: means that the
stove is on.
) Flashing LED: indicates that
stove firing is in progress or
that the stove is in standby
mode.
LED is dark: means that the
stove is off.
F
G
fig� 7�1
,