Advertisement
Quick Links
Advertisement
Related Manuals for Mikroe CLICKER 4 for STM32
Summary of Contents for Mikroe CLICKER 4 for STM32
- Page 1 C L I C K E R 4 f o r S T M 3 2 U S E R M A N U A L...
- Page 2 Thank you for choosing Mikroe! We present you the ultimate solution for embedded development. Elegant on the surface, yet extremely powerful on the inside, we have designed it to inspire outstanding achievements. And now, it’s all yours. Enjoy premium. Time-saving embedded tools...
-
Page 3: Table Of Contents
Table of contents Introduction 1. Key microcontroller features 2. MCU programming 3. MCU Reset 4. Buttons and LEDs 5. Power supply 6. Connectivity 7. Click boards ™... -
Page 5: Introduction
Clicker 4 for STM32 is a compact development board Besides two 1x23 pin headers, four improved mikroBUS ™ designed as a complete solution, you can use it to quickly sockets represent the most distinctive connectivity feature, build your own gadgets with unique functionalities. -
Page 6: Key Microcontroller Features
∫ Operating frequency up to 216 MHz ∫ 462 DMIPS/2.14 DMIPS/MHz (Dhrystone 2.1). For the complete list of MCU features, please refer to the STM32F767BI datasheet CLICKER 4 for STM32 U S E R M A N U A L... -
Page 7: Mcu Programming
Based on the used programmer/ Figure 2: Clicker 4 for STM32 with CODEGRIP connected debugger tool pinout, a coresponding addapter might be needed. CLICKER 4 for STM32 U S E R M A N U A L... -
Page 8: Mcu Reset
The RST pin of the host MCU is also routed to the pin 1 of the 1x23 pin header (4), allowing an external signal to reset the MCU. Figure 3: Clicker 4 for STM32 front view CLICKER 4 for STM32 U S E R M A N U A L... -
Page 9: Buttons And Leds
Each LED is connected to a MCU pin, and an active LED indicates that a logic high (1) is present. Figure 4: Buttons and LEDs view CLICKER 4 for STM32 U S E R M A N U A L... -
Page 10: Power Supply
USB-C connector Standard 2.5mm pitch XH battery connector Figure 5: Power supply view CLICKER 4 for STM32 U S E R M A N U A L CLICKER 4 for STM32 U S E R M A N U A L... -
Page 11: Connectivity
MCU pins. Figure 6: Front view with connected USB - C cable CLICKER 4 for STM32 U S E R M A N U A L CLICKER 4 for STM32 U S E R M A N U A L... - Page 12 SDI1 3.3V SDO1 SCK2 SDI2 SDO2 INTERRUPT SCL1 SDA1 SCL2 SDA2 ANALOG UART DIGITAL CAN-RX CAN-TX Figure 7: 1x23 pin header view INTERRUPT UART ANALOG DIGITAL CLICKER 4 for STM32 U S E R M A N U A L...
-
Page 13: Click Boards
These ready-to-use boards require no additional hardware configuration. More information at www.mikroe.com/click Figure 8: Clicker 4 for STM32 with NFC 2 click connected CLICKER 4 for STM32 U S E R M A N U A L... - Page 14 A NEW IDEA IS JUST A CLICK AWAY.
- Page 15 D I S C L A I M E R All the products owned by MikroElektronika are protected by copyright law and international copyright treaty. Therefore, this manual is to be treated as any other copyright material. No part of this manual, including product and software described herein, must be reproduced, stored in a retrieval system, translated or transmitted in any form or by any means, without the prior written permission of MikroElektronika.
- Page 16 If you are experiencing some problems with any of our products or just need additional information, please place your ticket at www.mikroe.com/support Time-saving embedded tools If you have any questions, comments or business proposals, do not hesitate to contact us at office@mikroe.com...
Need help?
Do you have a question about the CLICKER 4 for STM32 and is the answer not in the manual?
Questions and answers