DFI KD331-C236/Q170 User Manual page 36

SATA Configuration (KD331-Q170)
This section is designed to select the SATA controller and the type of hard disk drive which are
installed in your system unit.
InsydeH2O Setup Utility
Advanced
SATA Controller(s)
SATA Speed
SATA Mode Selection
Serial ATA Port 0 [Not Installed]
Port 0
Hot Plug
Serial ATA Port 1
[Not Installed]
Port 1
Hot Plug
Serial ATA Port 2
[Not Installed]
Port 2
Hot Plug
Serial ATA Port 3
[Not Installed]
Port 3
Hot Plug
Serial ATA Port 4
[Not Installed]
Port 4
Hot Plug
Serial ATA Port 5
[Not Installed]
Port 5
F1 Help ↑/↓ Select Item F5/F6
Esc Exit ←/→  Select Item Enter
SATA Controller(s)
This field is used to enable or disable Serial ATA devices.
SATA Speed
This field is used to select SATA speed generation limit: Auto, Gen1, Gen2 or Gen3.
SATA Mode Selection
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Inter-
face).
Intel RST Premium Mode
This option allows you to create RAID or Intel Matrix Storage configuration on Serial
ATA devices.
Serial ATA Port 0, 1, 2, 3, 4, 5 and Hot Plug
These fields are used to enable or disable the serial ATA port and its hot plug. Serial
ATA Port 5 is used to configure SATA signal of M.2.
Chapter 3 BIOS Setup
Chapter 3
Rev. 5.0
Enable/Disable SATA
<Enabled>
Device.
<Auto>
<AHCI>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
Change Values F9 Setup Defaults
Select SubMenu F10 Save and Exit

SATA Configuration (KD331-C236)
This section is designed to select the SATA controller and the type of hard disk drive which are
installed in your system unit.
Advanced
SATA Controller(s)
SATA Speed
SATA Mode Selection
System Acceleration with Intel(R)
Optane(TM) Memory
Serial ATA Port 0 [Not Installed]
Port 0
Hot Plug
Serial ATA Port 1 [Not Installed]
Port 1
Hot Plug
Serial ATA Port 2 [Not Installed]
Port 2
Hot Plug
Serial ATA Port 3 [Not Installed]
Port 3
Hot Plug
Serial ATA Port 4 [Not Installed]
Port 4
Hot Plug
Serial ATA Port 5 [Not Installed]
Port 5
F1 Help ↑/↓ Select Item
Esc Exit ←/→ Select Item

SATA Controller(s)
This field is used to enable or disable Serial ATA devices.
SATA Speed
This field is used to select SATA speed generation limit: Auto, Gen1, Gen2 or Gen3.
SATA Mode Selection
The mode selection determines how the SATA controller(s) operates.
AHCI Mode
This option allows the Serial ATA devices to use AHCI (Advanced Host Controller Inter-
face).
Intel RST Premium With Intel Optane System Acceleration Mode
This option allows you to create RAID or Intel Rapid Storage configuration with Intel
Optane™ system acceleration on Serial ATA devices.
System Acceleration with Intel(R) Optane(TM) Memory
This field is used to enable or disable the system acceleration with Intel
memory feature.
36
InsydeH2O Setup Utility Rev. 5.0
Enable/Disable SATA
<Enabled>
Device.
<Auto>
<AHCI>
<Enabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
<Disabled>
<Enabled>
F5/F6 Change Values F9 Setup Defaults
Enter Select SubMenu F10 Save and Exit

Optane™
®
www.dfi .com
®