Table of Contents
Related Manuals for Kendal Lighting AC-24144
Summary of Contents for Kendal Lighting AC-24144
- Page 1 READ AND SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS Model: AC-24144 Kendal Lighting (BC) Inc. #110, 6780 Dennett Place Delta, BC V4G 1N4 Canada Tel: (604) 952-5510 Fax: (604) 952-5513 CETL LISTED MODEL: BF858 Weight of Fan: 5.5 Kgs...
-
Page 2: Tools And Materials Required
1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: Blade set (3) Hanger bracket Canopy Canopy cover Downrod assembly Coupling cover Fan motor assembly LED light kit... -
Page 3: Safety Rules
3. SAFETY RULES 1. To reduce the risk of electric shock, insure 7. For fans with manual reverse, do not electricity has been turned off at the circuit operate reversing switch while fan blades are in motion. Fan must be turned off and breaker or fuse box before beginning. -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing CUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. -
Page 5: Hanging The Fan
5. HANGING THE FAN REMEMBER to turn off the power. Follow the CUL Listed steps below to hang your fan properly: electrial Step 1. Pass the 120-volt supply wires through Hanger Washers bracket the center hole in the ceiling hanger bracket as shown in Fig. -
Page 6: Make The Electric Connections
6. MAKE THE ELECTRIC CONNECTIONS Code switch WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. NOTE: This remote control unit is equipped with 16 code combinations to prevent possible Figure 8 interference from or to other remote units. -
Page 7: Installation Of Safety Support
Note: Fan must be installed at a maximum distance of 20 feet from the transmitting unit for proper signal transmission between the transmitting unit and the fan's receiving unit. 7. INSTALLATION OF SAFETY SUPPORT Hanger bracket Safety cable An additional safety cable is provided to prevent the fan from falling. -
Page 8: Attaching The Fan Blades
9. ATTACHING THE FAN BLADES Step 1. Remove the nine blade screws from the fan motor assembly. (Fig. 13) Step 2. Insert the blades through the slots on Fan motor assembly the fan motor assembly. Attach the blade to the fan motor assembly using three blade screws. - Page 9 11. INSTALLING THE Outlet box TRANSMITTER Switch HOLDER Wall plate Select a location to install your remote control system transmitter. You can replace an existing wall switch or, install the transmitter on ANY flat surface. Option 1: Install the remote control system using an existing wall switch outlet box.
-
Page 10: Installing The Battery
12. INSTALLING THE BATTERY Remove the back cover on the transmitter and install both, 3 volt (#2032) batteries that were included with the remote control. Make sure the + sign is facing up. (Fig. 19) 13. OPERATING YOUR TRANSMITTER Figure 19 Restore power to ceiling fan and test for proper operation. -
Page 11: Care Of Your Fan
14. CARE OF YOUR FAN Here are some suggestions to help maintain your fan. 1. Because of the fan's natural movement some connections may become loose. Check the support connections, brackets and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from the ceiling). -
Page 12: Troubleshooting
15. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. 3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.