Cleaning Agents; Detaching And Refitting The Rails - Bosch HBM43B250A Instruction Manual

Cleaning agents

To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
sharp or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
■
Wash new sponge cloths thoroughly before use.
Area Cleaning agents
Oven front Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
glass scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues.
Special stainless steel cleaning prod-
ucts suitable for warm surfaces are avail-
able from our after-sales service or from
specialist retailers. Apply a thin layer of
the cleaning product with a soft cloth.
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Glass cover for the Hot soapy water:
oven light Clean with a dish cloth.
Seal Hot soapy water:
Do not remove. Clean with a dish cloth. Do not scour.
Shelves Hot soapy water:
Soak and clean with a dish cloth or
brush.
Telescopic shelves Hot soapy water:
Clean with a dish cloth or a brush. Do
not soak or clean in the dishwasher.
Accessories Hot soapy water:
Soak and clean with a dish cloth or
brush.
Cleaning self-cleaning surfaces in the cooking compartment
The back panels, ceiling and side panels of the cooking
compartment are coated with self-cleaning enamel. This
coating absorbs and dispels splashes from baking and
roasting while the oven is in operation. The higher the
temperature and the longer the oven is in operation the better
the result will be.
If dirt is still visible after operating the oven several times, clean
the back panel, ceiling and side panels with hot soapy water
and a soft cloth.
Over time, discolourations may occur, which can no longer be
removed. These will not damage the enamel.
Caution!
Damage to surfaces on self-cleaning areas due to applying
oven cleaner.Never clean the self-cleaning surfaces with oven
cleaner.
If oven cleaner accidentally gets onto self-cleaning surfaces,
remove it immediately with a sponge and plenty of water.
Caution!
Damage to surfaces on self-cleaning areas due to the use of
abrasive and acidic cleaning agents and aids.
Do not use cleaning agents containing abrasive substances or
acids.
Do not use abrasive cleaning aids such as steel wool or
scourers.
Cleaning the cooking compartment floor
Use a dish cloth and hot soapy water or a vinegar solution.
If there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.

Detaching and refitting the rails

The rails can be removed for cleaning. The oven must have
cooled down.
Detaching the rails
Lift up the front of the rail
1.
and unhook it (figure A).
2.
Then pull the whole rail forward
3.
and remove it (Fig. B).
4.
$


Clean the rails with cleaning agent and a sponge. For stubborn
deposits of dirt, use a brush.
Refitting the rails
First insert the rail into the rear socket, press it to the back
1.
slightly (figure A),
and then hook it into the front socket (figure B).
2.
$
The rails fit both the left and right sides. Ensure that, as shown
in figure B, levels 1 and 2 are below and levels 3, 4 and 5 are
above.
%


%
11