Summary of Contents for Ilsco TASKMASTER TOOLS TB-CUT40CU-IS
Page 1
Model: TB-CUT40CU-IS Instruction manual Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. TASKMASTER TOOLS Phone: 4730 Madison Road 800-776-9775 Cincinnati OH 45227 513-533-6200 www.ilsco.com...
Your first reconditioning is on us! Call us after about 20,000 cycles. To Find a TASKMASTER PRO Service Partner Call ILSCO for assistance in solving tool performance issues or for any of your service needs. ILSCO tool owners will be offered options to solve any tool replacement, parts or repair issues.
TB-CUT40CU-IS SAFETY Read all safety warnings, instructions provided with this battery operated tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. WORK AREA SAFETY •...
Page 5
TB-CUT40CU-IS • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. • Use the battery operated accessories in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the tool for operations different from those intended could result in a hazardous situation.
TB-CUT40CU-IS TECHNICAL SPECIFICATIONS Force developed: 3.3 tons Jaw opening 1.5 in. Battery voltage: 18 V Battery capacity: 2.0 Ah Type of battery: Lithium-ion Charging time: 60 min (approx) Hydraulic oil: Shell Tellus S2 V 15 Operating temperature range: -4° to 122° (F) Dimensions: 16.61 x 4.96 x 3.23 (L x H x W) Weight:...
TB-CUT40CU-IS BATTERY CHARGER Charge only MILWAUKEE M18™ Li-Ion batteries in this MILWAUKEE Li-Ion charger. Other types of batteries may cause personal injury and damage. WHEN TO CHARGE THE BATTERY PACK WITH THIS MILWAUKEE CHARGER Remove the battery pack from the tool for charging when convenient for you and your job. MILWAUKEE batteries do not develop a memory when charged after only a partial discharge It is not necessary to run down the battery pack before placing it on the charger.
Page 11
TB-CUT40CU-IS CHARGING A HOT OR COLD BATTERY PACK The Red Flashing Indicator light on the charger indicates that the battery pack temperature is outside the charging range. Once the battery pack is within the acceptable range, normal charging will take place and the red light will be continuous. Hot or cold batteries may take longer to charge. POWER THE CHARGER WITH AN INVERTER OR GENERATOR The charger will operate with most generators and inverters rated at 350 Watts or higher.
TB-CUT40CU-IS BATTERY PACK FUEL GAUGE Use the Fuel Gauge to determine the battery pack‘s remaining run time. Press the Fuel Gauge button to display the lights. The Fuel Gauge will light up for 2-3 seconds. When less than 10% of charge is left, 1 light on the fuel gauge will flash slowly.
Page 13
TB-CUT40CU-IS COLD WEATHER OPERATION MILWAUKEE Li-Ion battery packs are designed to operate in temperatures below freezing. When the battery pack is too cold, it may need to warm up before normal use. Put the battery on a tool and use the tool in a light application. It may buzz for a short time until it warms up. When the buzzing stops, use the tool normally.
TB-CUT40CU-IS OPERATING INSTRUCTIONS Be sure to read instructions carefully, wear safety goggles, and keep fingers away from cutting head. ATTACHING THE BATTERY TO THE TOOL While pressing the two side buttons, pull out the battery cartridge. To replace the battery cartridge, push the new cartridge firmly into place.
TB-CUT40CU-IS ADVANCE TRIGGER AND RELEASE BUTTON The cutting head jaws move together when the advance trigger is pressed and stops when the trigger is released. To release the cutting head jaws, press the release button. CUTTING Retract the cutting head jaws fully by pressing the release button. Place the wire between the cutting head jaws.
TB-CUT40CU-IS BATTERY STATUS LIGHTS Fault Cause / Solution At the end of the cutting cycle No light No malfunction Red flashing light Charge / substitute the battery (about 10% of the capacity) Red light Flat battery After inserting the battery Green light No malfunction Red light...
1024 x 768 or higher, at least 65,535 colors Other: USB 2.0 How to Download Software Go to www.ILSCO.com Click the Technical Resources tab Under the Technical Resources header, click on the Tool Software link Locate your tool‘s software Plug & Play...