Related Manuals for Wren Kitchens Vogue BASE UNIT 600 2 Drawer
Summary of Contents for Wren Kitchens Vogue BASE UNIT 600 2 Drawer
- Page 1 BASE UNIT 600 2/3 Drawer Assembly Guide 2 Drawer 600 2 Drawer inc 3 Drawer Dummy Drawer For Internal Use: FI.WR.INS.025_WKIN00107_BASE_600_2_3Drawer_2DrwIncDummy_Rev5.indd...
-
Page 2: Before You Start
BASE UNIT 600 2/3 Drawer Assembly Guide BEFORE YOU START INSTALLATION SHOULD BE PERFORMED BY A COMPETENT PERSON ONLY. THIS PRODUCT COULD BE DANGEROUS IF INCORRECTLY INSTALLED Standard Drawer (Packed Separately) Fitting Pack Contents METAL BACK PANEL (J) x16 (Q) x4 (N) x1 Drawer Runner 21mm... - Page 3 Step 1. Secure drawer base to drawer side using 4 x 16mm drawer runner screws (J) in holes provided. Seat the edge of drawer base tight Drawer into corner of casing, as shown. base The decorative face of drawer base to be positioned as shown.
- Page 4 BASE UNIT 600 2/3 Drawer Assembly Guide Step 1. Secure drawer base to drawer side using 4 x 16mm drawer runner screws (J) in holes provided. Drawer base Seat the edge of drawer base tight white decorative Metal face up into corner of casing, as shown.
- Page 5 600 Drawer Unit Contents BEFORE YOU START INSTALLATION SHOULD BE PERFORMED BY A COMPETENT PERSON ONLY. THIS PRODUCT COULD BE DANGEROUS IF INCORRECTLY INSTALLED Panel B Panel A Panel E Panel C x2 End Panel x1 Back Panel x2 Rail Panel x1 Base Panel (F) x12 (G) x8...
- Page 6 BASE UNIT 600 2/3 Drawer Assembly Guide Drawer runner bracket screw position Panel B Step 1. To attach drawer runner screw into end panels (B) using 2 x 16mm screws (J) per drawer rail, into pilot holes provided, as shown. Part B Step 2.
- Page 7 Step 3. Step 4. Seat dowel (F) Seat cam dowel (G) into into holes in both end holes in both end panels (B) Seat (G) cam dowel panels (B) as shown. as shown. into hole as shown. Dowel (F) & Cam Dowel (G) location detail Step 5.
- Page 8 BASE UNIT 600 2/3 Drawer Assembly Guide Step 6. Slide back panel (A) into groove of end panels (B). Once back panel (A) is in position, ensure the panel is flush & square with bottom of end panels (B). Step 7. Hand tighten all cam locks (H), this will expand cam dowels (G) and tighten the unit together.
- Page 9 Front Step 9. Position legs as shown. Ensure legs are rotated to also provide support to the end panels (B). Front Leg position diagram Step 10. Secure each of the legs into place with 4 x 15mm screws (L) per leg. Step 11.
- Page 10 BASE UNIT 600 2/3 Drawer Assembly Guide Screw into any side units using the 30mm screws (K) provided to secure to the unit. Screw just to the rear of the indentations at the top and bottom on sides of the unit where applicable. Place a cover cap (M) on the head of the screw to conceal it.
- Page 11 Dummy Draw Frontal Fixing (Where Applicable) Drawers Supplied in accordance to Specific Customer Kitchen Plan Part A Part B 2 Drawer inc Dummy Fixing Clip Dummy Drawer Step 1. Secure 2 x dummy fixing clip parts (B) onto the inside face of dummy draw front, 22mm from the edge spaced evenly either Part B side as shown, using 1 x 21mm screw (Q) per part (B).
Need help?
Do you have a question about the Vogue BASE UNIT 600 2 Drawer and is the answer not in the manual?
Questions and answers