Subscribe to Our Youtube Channel
Related Manuals for MSI MS-5192
Summary of Contents for MSI MS-5192
- Page 1 Chapter 1 INTRODUCTION The MS-5192 mainboard is a high-performance all-in-one mainboard based ® on Cyrix GXM/GX-LV processor. It combines Audio/Video chip integrated ® with Realtek 8139B 10/100M Ethernet .
-
Page 2: Mainboard Features
1.1 Mainboard Features ® Cyrix Media GXm/GXLV 200/233Mhz processor Chipset Cyrix CX5530 chipset. NS PC97317 Super I/O Main Memory Support one memory banks using 168-pin unbuffered DIMM. Support a maximum memory size of 64MB. Support 3.3v SDRAM DIMM. Flash Memory 8MB Flash Disk On-Board IDE Connect one IDE devices. - Page 3 Network Realtek 8139B 10/100M Ethernet - WFW baseline & NET PC specs compliant - ACPI - Magic packet filtering to wake-up on LAN - ARP & Flexible frame filtering - Software drivers are backwards compatible Parallel Port One Parallel port bi-directional centronics compatible DB-25. Two Serial Port Connectors Type Serial Port A: DB-9 male connector with RS-232C.
-
Page 4: Mainboard Layout
1.2 Mainboard Layout T: LPT T: mouse USB Ports L-OUT MIC-IN VGA Port B: COM A/COM B Keyboard Super I/O 97317 RTL8139B Socket 7 JCKM1 ® Cyrix CX5530 Chipset BATT JFAN1 JBAT1 JFP1 MS-5192 Mainboard... -
Page 5: Hardware Installation
Chapter 2 HARDWARE INSTALLATION ® The mainboard operates with Cyrix GXM/GX-LV processor. The mainboard uses a CPU socket called Socket 7 for easy CPU installation. The CPU should always have a Heat Sink and a cooling fan attached to prevent overheating. -
Page 6: Cpu Core Speed Derivation Procedure
2.1-2 CPU Core Speed Derivation Procedure 1. The Jumper Switch JCKM1 (1-2, 3-4, and 5-6) is used to set the Core/Bus (Fraction) ratio of the CPU. The actual core speed of the CPU is the Host Clock Frequency multiplied by the Core/Bus ratio. For example: CPU Clock 33.3MHz Core/Bus ratio... - Page 7 2.1-3 CPU Voltage Setting: SW1 To adjust the voltage setting of the CPU, you must know the specifications of your CPU (always ask the vendor for CPU spec.). Voltage Setting (Vcore) 2.2V 2.9V...
- Page 8 2.1-4 Fan Power Connector: JFAN1 This connector support system cooling fan with +12V. It supports three pin head connector. When connecting the wire to the connector, always take note that the red wire is the positive and should be connected to the +12V, the black wire is Ground and should be connected to GND.
- Page 9 A battery must be used to retain the mainboard configuration in CMOS RAM. If you use the on-board battery, you must short 1-2 pins of JBAT1 to keep the CMOS data. JBAT1 Function JBAT1 Keep Data Clear Data Note: You can clear CMOS by shorting 2-3 pin, while the system is off. Then, return to 1-2 pin position.
-
Page 10: Memory Bank Configuration
2.3-1 Memory Bank Configuration The mainboard supports a maximum of 64MB of memory : It provides one 168-pin DIMMs (Double In-Line Memory Module) sockets. It supports 8 MB to 64 Mbytes DIMM memory module. The memory module can only support SDRAM(Synchronous DRAM) MODE DRAM. There are two kinds of DIMM specification supported by this mainboard: PC100 and PC66. -
Page 11: Memory Installation Procedures
2.3-2 Memory Installation Procedures: A. How to install a DIMM Module Single Sided DIMM Double Sided DIMM 1. The DIMM slot has a two Notch Key “VOLT and DRAM”, so the DIMM memory module can only fit in one direction. 2. -
Page 12: Memory Population Rules
2.3-3 Memory Population Rules 1. Supports SDRAM DIMM. 2. Supports 3.3 volt DIMM. 3. The DRAM addressing and the size supported by the mainboard is shown below: Table 2.3-1 SDRAM Memory Addressing DRAM MB/DIMM Address Size DRAM DRAM Density & Addressing Tech. - Page 13 The Keylock, Power Switch, Reset Switch, Power LED, Speaker, and HDD LED are all connected to the JFP1 connector block. Buzzer Speaker (short Reset pin) Switch Keylock Dual Color Single Power Color Switch Power LED JFP1...
- Page 14 2.4-1 Power Switch Connect to a 2-pin push button switch. This switch has the same feature with JRMS1. 2.4-2 Reset Switch Reset switch is used to reboot the system rather than turning the power ON/ OFF. Avoid rebooting while the HDD LED is lit. You can connect the Reset switch from the system case to this pin.
- Page 15 The Power LED, LAN LED, and Power Swich are all connected to the J9 connector block. Power Switch Power 2-11...
-
Page 16: Pin Definition
The mainboard provides two 9-pin male DIN connectors for serial port COM A and COM B. These port are 16550A high speed communication ports that send/receive 16 bytes FIFOs. You can attach a mouse or a modem cable directly into this connector. 1 2 3 4 5 6 7 8 9 COM B... - Page 17 The mainboard provides a 25 pin female centronic connector for LPT. A parallel port is a standard printer port that also supports Enhanced Parallel Port(EPP) and Extended capabilities Parallel Port(ECP). See connector and pin definition below: 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 PIN DEFINITION SIGNAL...
- Page 18 ® The mainboard provides a standard PS/2 mouse mini DIN connector for ® ® attaching a PS/2 mouse. You can plug a PS/2 mouse directly into this connector. The connector location and pin definition are shown below: Pin5 Mouse Clock Pin6 Pin3 ®...
- Page 19 The mainboard provides a RJ-45 connector for your network need. RJ-45 Connector 2-15...
- Page 20 Line Out is a connector for Speakers or Headphones. Mic In is used for inserting External Maicrophone. Mic In Line Out 1/8” Stereo Audio Connectors 2-16...
- Page 21 The mainboard provides a UHCI(Universal Host Controller Interface) Universal Serial Bus root for attaching USB devices like: keyboard, mouse and other USB devices. You can plug the USB device directly to this connector. USB Port 2 1 2 3 4 USB Port 1 SIGNAL -Data0...
Need help?
Do you have a question about the MS-5192 and is the answer not in the manual?
Questions and answers