Outdoor GreatRoom Company Kenwood Dining Table Installation Instructions Manual

Outdoor GreatRoom Company Kenwood Dining Table Installation Instructions Manual

Advertisement

Quick Links

Kenwood Dining Table
Installation Instructions for Kenwood Dining Table
KW-1242-K
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Kenwood Dining Table and is the answer not in the manual?

Questions and answers

Summary of Contents for Outdoor GreatRoom Company Kenwood Dining Table

  • Page 1 Kenwood Dining Table Installation Instructions for Kenwood Dining Table KW-1242-K...
  • Page 2: Table Of Contents

    IMPORTANT Contents Please consult your Crystal Fire instruction manual for detailed instructions and important information related to the burner Required Tools…………………………….…..2 installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches. Included with your Fire Pit……………….3 DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT Assembly Instructions………………….………4 FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
  • Page 3: Included With Your Fire Pit

    Included with your Fire Pit Touch-Up Bolt A [40X] Paint Bottle [1X] M6X20 Corner Support Bracket [12X] Leg A (1X) Leg B (1X) Leg C (2X) M6 Allen Wrench [1X] CFP1242 Burner [1X] Top [1X] Panel A [2X] Panel B [1X] Access Door [1X] Center Support [1X] Front Support [1X]...
  • Page 4: Assembly Instructions

    Assembly Instructions Included with your Fire Pit INSTALL NOTE: Final tightening of bolts should be completed following installation of all panels and legs. A. 4 Fasteners B. 4 B-Bolts 1. Unpack all the contents from the box and remove the individual packaging from each component.
  • Page 5 3. Attach Corner Support Brackets to all corners of legs as shown below. Attach 4X brackets to each Leg C, attach 3X bracket to Legs A and B. Brackets attach using Bolt A (1X). Tighten bolts to help stabilize side panel when attaching. 4.
  • Page 6: Gas Connections

    Attach Panel B using Bolt A (4X) as shown below. 6. Attach Center Support, as shown below, to the bottom of the fire pit using Bolt A (4X). NOTE: Drainage holes on Center Support piece must be facing down towards the surface on which you will be placing your fire pit.
  • Page 7: Position Your Tank

    8. Do a final tightening of the bolts you have installed in your fire pit. Then, with the help of another person, turn the table right side up. CF-SPARKER Installation Locate CF-SPARKER inside of Crystal Fire Plus burner box.  ...
  • Page 8: Igniter Installation

    Gas Connections Read and understand your Crystal Fire Plus owner’s manual before beginning burner hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings.  See Crystal Fire Plus instructions for burner installation.  All gas connections were completed at the factory.
  • Page 9: Thermocouple Installation

    Thermocouple Installation • Refer to Crystal Fire Plus instruction manual for detailed attachment of thermocouple. • Attach thermocouple to burner valve as shown below. control valve. TIGHTEN SECURELY WITH A WRENCH Electrode Installation  Plug both BLACK wires hanging from the burner into the back of the CF-SPARKER.
  • Page 10: Glass Installation

    Glass Installation 1. Scatter all of the included Glass Beads evenly onto burner surface. DO NOT OPERATE CRYSTAL FIRE PLUS BURNER WITHOUT GLASS BEADS OR OTHER DECORATIVE MEDIA PRESENT DO NOT OPERATE CRYSTAL FIRE PLUS BURNER WITH GLASS COVER IN PLACE...
  • Page 11: Position Your Tank

    After installing CF-SPARKER and making gas connections, verify that all connections are tight and that no leaks are present using a solution of soapy water or a commercially available leak-check solution. Position Your Tank (If Applicable) 1. Connect the propane hose/regulator to the propane tank and hand tighten (DO NOT USE A WRENCH) and slide the propane tank past the dotted line to ensure the Access Door closes properly.
  • Page 12 IMPORTANT Please consult your Crystal Fire Plus instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches. DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE PLUS BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE PLUS OWNER’S MANUAL.

This manual is also suitable for:

Kw-1242-k

Table of Contents