Subscribe to Our Youtube Channel
Related Manuals for Outdoor GreatRoom Company KW-1242-K
Summary of Contents for Outdoor GreatRoom Company KW-1242-K
- Page 1 Kenwood Dining Table Installation Instructions for Kenwood Dining Table KW-1242-K...
-
Page 2: Table Of Contents
IMPORTANT Contents Please consult your Crystal Fire instruction manual for detailed instructions and important information related to the burner Required Tools…………………………….…..2 installation including: lighting and operating instructions, safety Included with your Fire Pit……………….3 information, and proper tightening of connections with two wrenches. DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT Assembly Instructions………………….………4 FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL. -
Page 3: Included With Your Fire Pit
Included with your Fire Pit Touch-Up Gas Valve Kit Bolt A [34X] Paint Bottle TOUCH PAINT [1X] M6X20 Mounting Gas Valve [1X] screws [2X] Corner Support Bracket [6X] M6 Allen Control knob Wrench [1X] [1X] CF-1242 Burner [1X] Leg A (1X) Leg C (2X) Leg B (1X) Panel A [2X]... -
Page 4: Assembly Instructions
Assembly Instructions Included with your Fire Pit INSTALL NOTE: Final tightening of bolts should be completed following installation of all panels and legs. A. 4 Fasteners B. 4 B-Bolts 1. Unpack all the contents from the box and remove the individual packaging from each component. - Page 5 3. Attach Corner Support Brackets to all base corners of legs as shown below. Attach 2X brackets to each Leg C, attach 1X bracket to Legs A and B. Brackets attach using Bolt A (1X). Tighten bolts to help stabilize side panel when attaching. 4.
- Page 6 Attach Panel B using Bolt A (4X) as shown below. Drainage holes NOTE: Drainage holes on Panel B must be facing down towards the surface on which you will be placing your fire pit. 6. Attach Center Support, as shown below, to the bottom of the fire pit using Bolt A (4X).
-
Page 7: Contents Position Your Tank
7. On the access door side, attach Access Door Side the Front Support to Legs A and B using Bolt A (4X). Attach support plate to legs 8. Do a final tightening of the bolts you have installed in your fire pit. Then, with the help of another person, turn the table right side up. -
Page 8: Igniter Installation
9. Hold the Gas Valve in place from behind the control panel as shown while inserting the two included Mounting Screws. Use a Phillips screwdriver to fasten. Attach control knob by pressing on to the valve stem. Bottom Insert screws included with Gas Valve Kit... -
Page 9: Gas Connections
Gas Connections Read and understand your Crystal Fire owner’s manual before beginning burner hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings. 1. Reach inside the burner cut-out and attach natural gas supply line using a 3/8”... - Page 10 3. Set Burner into the fire pit base as shown below. Electrode Access Door 4. Attach flex line from the burner to gas valve as shown below. TIGHTEN CONNECTION SECURELY WITH WRENCH Metal flex line to burner ONLY...
-
Page 11: Cf-Sparker Installation
CF-Sparker Installation 1. Make sure the valve is in the OFF position before beginning. 2. Install sparker as shown, using a AAA battery (not included). Negative end should be placed inside the CF-SPARKER, positive end outside of the CF-SPARKER. CF-Sparker will not operate correctly without an ignition and ground wire attached. -
Page 12: Glass Installation
Glass Installation 1. Scatter all of the included Glass Beads evenly onto burner surface. DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT GLASS BEADS OR OTHER DECORATIVE MEDIA PRESENT DO NOT OPERATE CRYSTAL FIRE BURNER WITH GLASS COVER IN PLACE... -
Page 13: Position Your Tank
After installing CF-Sparker and making gas connections, verify that all connections are tight and that no leaks are present using a solution of soapy water or a commercially available leak-check solution. Position Your Tank (If Applicable) 1. Connect the propane hose/regulator to the propane tank and hand tighten (DO NOT USE A WRENCH) and slide the propane tank past the dotted line to ensure the Access Door closes properly. - Page 15 IMPORTANT Please consult your Crystal Fire instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches. DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
- Page 16 14400 Southcross Drive West • Suite 100 • Burnsville, MN 55306 Toll Free: 1-866-303-4028 • Sales@OutdoorRooms.com...
Need help?
Do you have a question about the KW-1242-K and is the answer not in the manual?
Questions and answers