Advertisement
Quick Links
Operation Manual
AOYUE Repairing/Hot Air Soldering Station
902703A+
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec AOYUE Int2703A+
Summary of Contents for WilTec AOYUE Int2703A+
- Page 1 Operation Manual AOYUE Repairing/Hot Air Soldering Station 902703A+ Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Read all safety instructions and warnings. Failure to follow the safety instructions could result in electric shock, fire and/or serious injury. Keep all safety notices and instructions for future use. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 3 http://www.WilTec.de...
- Page 4 The heat gun, the soldering iron and the desoldering gun have an adjustable automatic sleep function. Five different reworking profiles can be saved, so that constant work can be guaranteed auto - matically. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 4 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 5 Compatible with many different soldering tips Five programmable profiles Heating element and soldering tip combined in one component, thus enabling easy replacement User-configurable sleep (“auto sleep”) © by WilTec Wildanger Technik GmbH Item 902703A+ Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 Cleaning tip Soldering iron holder and tin-solder holder Filter pads Electric cable End cap Hot air nozzles 1124, Vacuum suction pen 1130, 1197, 1313, 1919, 1010 © by WilTec Wildanger Technik GmbH Item 902703A+ Page 6 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 7 1. Connect the cable to the 6-pin socket on the device (9). 2. Connect the vacuum hose to the socket provided (7). 3. Place the desoldering gun in its holder to prepare for use. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 7 http://www.WilTec.de...
- Page 8 2. Make sure that all function switches are set to Off before you operate the main switch (10) of the station. 3. The product name is briefly displayed in ticker and then “OFF” on the display panels. This dis- play remains until the user activates a function. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 4. Use the temperature setting button of the hot air function to set the desired temperature. You can change the time using the air flow control button. To switch between the individual levels, simply press the hot air piston function key repeatedly. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 9 http://www.WilTec.de...
- Page 10 8. When you have completed the work, switch off the fume extraction system. 9. Switch off the soldering iron function. 10. Let the soldering iron cool down before packing it up. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 10 http://www.WilTec.de...
- Page 11 6. Let the desoldering gun heat up. The tip takes about 5–6 min to heat up while the inner solder drain takes about 5–9 min longer to reach operating temperature. If the operating temperature © by WilTec Wildanger Technik GmbH Item 902703A+ Page 11 http://www.WilTec.de...
- Page 12 1. While the hot air iron is in standby (display fields 16 and 18 show “OFF”), press and hold the button to increase the air flow (3). © by WilTec Wildanger Technik GmbH Item 902703A+ Page 12 http://www.WilTec.de http://www.aoyue.eu...
- Page 13 7. Release the button when the temperature display field of the soldering function (14) shows “000.” You can now fine-adjust the soldering iron temperature. 8. You can use the temperature adjustment buttons to set the desired value. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 13 http://www.WilTec.de...
- Page 14 Handle tweezer with soldering tip 932.2 90198 Vacuum pick up kit for solder fume extraction ⌀ WQ/LF-52D 91537 Soldering station tip for soldering iron 5.2×1.2 mm © by WilTec Wildanger Technik GmbH Item 902703A+ Page 14 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 15 5. Insert the new heating element and reconnect the cable. Avoid any friction on the wire of the heating element. 6. Reconnect the earth after the heating element has been inserted. 7. Reinstall the handle. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 15 http://www.WilTec.de http://www.aoyue.eu...
- Page 16 № Name № Name Filter pad Heating element housing Filter holder Safety cap Desolderin gun body Filter pipe cap Heating element Filter spring Nozzle 10 Filter pipe © by WilTec Wildanger Technik GmbH Item 902703A+ Page 16 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 17 Push the filter holder back into place until you hear a click, which means that the filter holder is secured again. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 17 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 18 3. Reinstall the nozzle and slide the housing back into place. Tighten the locking screw again properly so that no air can escape. If the locking screw is not tightened properly, the desolder - ing gun can no longer heat up properly. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 18 http://www.WilTec.de...
- Page 19 Remaining residues, e. g. yellow discoloration, can now be removed with isopropanol alcohol. CAUTION: Never use a file to remove any residue! © by WilTec Wildanger Technik GmbH Item 902703A+ Page 19 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 20 In the tube there is an easily breakable quartz glass as an insulation material that must not be damaged. Loosen the cable connections and remove the heating element. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 20 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 21 Soldering 1. Apply solder paste. To solder the component (e. g. SMD) onto a circuit board, you need an adequate amount of solder paste. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 21 http://www.WilTec.de http://www.aoyue.eu...
-
Page 22: Troubleshooting
Restore the factory settings of the station. Switch the device on and off while holding down the “reduce hot air temperature” button. Wait until the display has finished tickering so that the device is reset to the factory settings. © by WilTec Wildanger Technik GmbH Item 902703A+ Page 22 http://www.WilTec.de... - Page 23 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.