Table of Contents
Advertisement
Quick Links
Operation Manual
ARTICLE 61538
Anti-Static Soldering Station
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH
Seite 11
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Advertisement
Table of Contents
Related Manuals for WilTec 61538
Summary of Contents for WilTec 61538
- Page 1 Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 11 http://www.WilTec.de http://www.aoyue.eu...
- Page 2 The information contained in this document is subject to change without prior notice. No part of this document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram.
-
Page 3: General Safety Instructions
The voltage of 230 Volt alternating voltage specified on the type plate of the device must correspond to the existing mains voltage. Never lift, transport or attach the device to the power cord. © by WilTec Wildanger Technik GmbH Seite 13 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... -
Page 4: Safety Rules
The operator is responsible for compliance with local safety and installation regulations. (Ask a qualified electrician if necessary) If the device should fail, repair work may only be carried out by a qualified electrician or by WilTec customer service. - Page 5 Unless they have been given su- pervision or instruction concerning the use of the appliance by a person that is responsible for their safety, they are not allowed to work with the station. © by WilTec Wildanger Technik GmbH Seite 15 http://www.WilTec.de http://www.aoyue.eu...
-
Page 6: Technical Data
5) While soldering do not give too much pressure on the iron tips. More pressure will not change the thermal conductivity and will result in damages of the iron tip. Technical Data © by WilTec Wildanger Technik GmbH Seite 16 http://www.WilTec.de http://www.aoyue.eu... -
Page 7: Wiring Diagramm
AC 24V +- 10% 50 Hz Tip of ground resistance <2ohm Tip of ground voltage <2mV Weight 1.58 (Common heater) 2.08 (Imported heater) Working temperature 0~40°C Storage temperature -20°C~80°C Storage humidity 35%~45% Wiring Diagramm © by WilTec Wildanger Technik GmbH Seite 17 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 8 3) The iron core must be welded off and replaced by the new heating core which can be fitted well and easily. Please remember or note down the previous iron core connection. © by WilTec Wildanger Technik GmbH Seite 18 http://www.WilTec.de...
- Page 9 Compatible Tips (Diameter 6.5 mm) © by WilTec Wildanger Technik GmbH Seite 19 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 10: Disposal Regulations
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.