Related Manuals for NSF Kasco CertiSafe PM-100
Summary of Contents for NSF Kasco CertiSafe PM-100
- Page 1 CertiSafe Pipe Mount ™ Assembly & Installation Manual 800 Deere Rd. Prescott, WI 54021 • 715-262-4488 • sales@kascomarine.com • www.kascomarine.com Document number 852113...
-
Page 2: Table Of Contents
PM-100 CERTISAFE™ PIPE MOUNT MANUAL Contents Safety First .......................3 Product and Installation Overview ..............4 Suggested Tools and Supplies .................4 Parts Included ....................5 Tank Penetration for Cable Support and Cord Grip ..........7 Mount Assembly ....................9 Cable Support ....................14 CertiSafe™ Tank Mixer Maintenance Recommendations ......15 CertiSafe™... -
Page 3: Safety First
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL IMPORTANT: PLEASE READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE SAFETY FIRST • Under NO circumstances should anyone enter the water with the mixer connected or in operation. • Running the unit out of water will create a dangerous situation and damage the seals. •... -
Page 4: Product And Installation Overview
• To prevent galling, we recommend a moisture-cured, polyurethane compound sealant suitable for contact with potable water and certified to meet the shrinkage for interior and exterior use. Refer to NSF/ANSI Standard 61 for indirect additives. • Be aware of clearance between the mixer assembly and any fixed objects within the tank, including ladders, ensuring that there is enough room for the CertiSafe™... -
Page 5: Parts Included
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL PARTS INCLUDED Assembly Item Description Quantity Part number Upper mount Upper mount base 997102 Upper mount pipe bracket 997117 Upper mount lock handle 997170 1/2”-13 x 1-3/4” serrated flange screw 840531 1/2”-13 x 1/4” shoulder screw 451114 Serrated flange nut 840530... - Page 6 Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL Steel tank roof Cord grip (S) 5/16” nylon locknut (O) Flat washer (P) Sealing washer (Q) Cable support (U) Cord grip nut (T) Flat washer (P) Eye bolt (N) Connecting link (R) Upper mount base (A) Serrated flange screw (D) Upper mount lock handle (C)
-
Page 7: Tank Penetration For Cable Support And Cord Grip
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL TANK PENETRATION FOR CABLE SUPPORT AND CORD GRIP Note: • The maximum tank roof thickness accommodated by the tank penetration parts included is 1/8”. • Suggested measurements are based on a 24” square access hatch. Tank hatch center point Ø... - Page 8 Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL 8. Fit a flat washer (P) and then the sealing washer (Q) onto 10. From the tank exterior, fit a second flat washer (P) onto the eye the eye bolt (N). bolt. 9.
-
Page 9: Mount Assembly
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL MOUNT ASSEMBLY With multiple options in both the upper and lower mount assemblies, the PM-100 allows for versatile adjustment of the unit’s position and angle within the tank. For ease of use and movement, Kasco recommends running the cable from the unit through the hollow center of the pipe. - Page 10 Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL Lower Mount Assembly 1. Slide the lower mount can strap (G) into position on the unit 3” from the cage, ensuring the clamp on the mixer cage is in line with the can strap flanges. Maintain alignment Cage clamp 3 inches...
- Page 11 Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL 5. Fit the strut-block assembly over the can strap, aligning the bottom holes on each strut with the screw and nut on the can strap flanges. Align with can strap hardware Fig. 14 Fig.
- Page 12 Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL Pipe Attachment 1. Pass the cable through the gap between the lower mount collar blocks (H). 2. Pass the length of cable through the center of the pre-cut stainless steel pipe. Fig. 19 Fig.
- Page 13 Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL Note: Steps 8 through 11 are best completed with two people. 8. Move the entire assembly into place over the installed upper mount base (A). 9. Align the slot of the pipe bracket (B) with the shoulder screw (E) installed in the upper mount base. 10.
-
Page 14: Cable Support
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL CABLE SUPPORT 1. Attach the cable support (U) to the connecting link (R). 3. Feed power cable through the cable support (U). 2. Close and tighten the connecting link. Fig. 28 Fig. 27 4. -
Page 15: Certisafe™ Tank Mixer Maintenance Recommendations
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL CERTISAFE™ TANK MIXER MAINTENANCE RECOMMENDATIONS CERTISAFE™ TANK MIXER MAINTENANCE RECOMMENDATIONS IMPORTANT: Disconnect electrical power prior to any maintenance or servicing! GFCI • If you note a deficiency in performance, remove the equip- •... -
Page 16: Certisafe™ Tank Mixer Warranty
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL CERTISAFE™ TANK MIXER WARRANTY THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED. IN NO EVENT WILL KASCO Kasco offers a standard 3-year warranty with the following MARINE, INC. BE LIABLE FOR ANY CONSEQUENTIAL models: DAMAGES. -
Page 17: Non-Warranty Repairs
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL NON-WARRANTY REPAIRS Kasco will recycle any unit we receive for estimate but which You can often repair failed equipment at a lower cost than re- placement. Kasco Marine estimates repairs at the request of the the customer declines to repair, unless the customer specifies otherwise. -
Page 18: Repair Contact Form
Back to Contents PM-100 CERTISAFE™ PIPE MOUNT MANUAL REPAIR CONTACT FORM • Kasco requires that all equipment sent for repair MUST be accompanied by this form and marked to Repairs attention. • Kasco is NOT responsible for shipping damage accrued in return shipment. •...