Related Manuals for Linak 239 Series
Summary of Contents for Linak 239 Series
- Page 1 TECH-system Type 239 For 2-parallel operation Instructions for installation and use...
-
Page 2: Preface
LINAK provides a warranty on all its products and systems. However, this warranty is provided on condition that the product is used in accordance with the applicable specifications, that maintenance is performed correctly, and that any repairs are carried out at a workshop that is authorised to repair LINAK products. -
Page 3: Important Information
The warranty is limited to the value of the LINAK product. The LINAK warranty shall only apply if the system has been used correctly and has not been opened. The control box and control unit must not be exposed to violent use. Failure to comply with this requirement will void the warranty. - Page 4 Warning! The plastic components in the system cannot withstand cutting oil. ______________________________________________________________________________ Page 4 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
-
Page 5: Table Of Contents
Operation ........................37 Initialisation ..............................37 Service operation .............................37 Troubleshooting ......................38 Reading errors ............................38 Disposal of LINAK products ..................39 ______________________________________________________________________________ Page 5 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 6: Technical Data
An externally connected display can be used to configure the motor control unit to operate various functions. For example, it is possible to adjust the acceleration/deceleration time, limit the stroke length, etc. The TECH-System type 239 is compatible with a range of different LINAK actuators. ______________________________________________________________________________ Page 6 of 39 june 2020 ver. -
Page 7: Motor Control Unit: (Pos.1)
Max. Current: Continuous current: 3.5A Transformer: 230/220 V – 150 Va Power supply in plastic box: Order no. TR-EM-000-T-230 ______________________________________________________________________________ Page 7 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 8: Actuator (Pos.3)
Order no. TR-1939.3314-00 • Rocker switch for building in: Other types of control devices can also be used. ______________________________________________________________________________ Page 8 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 9: Dimensions
TR-EM-239 for mounting on DIN rail TR-EM-239 mounted in plastic housing without for incorporating into an electrical panel power supply ______________________________________________________________________________ Page 9 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 10: Rating Plate And Labelling
Weight: approx. 300 gram Rating plate and labelling Rating plate on TR-EM-239 control unit: Rating plate on actuator LA31 w/Reed ______________________________________________________________________________ Page 10 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 11: Declaration Of Incorporation
Instruction Manual for TECH-system type 239 Declaration of Incorporation ______________________________________________________________________________ Page 11 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 12: Connection And Installation
The PCB is fitted using four 3 mm diameter screws and connected to an external power supply. The height of the PCB is 25 mm. ______________________________________________________________________________ Page 12 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... - Page 13 PCB fitted on DIN rail for panel installation – TR-EM-239-R The PCB is mounted on a DIN rail and connected to an external power supply. ______________________________________________________________________________ Page 13 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
- Page 14 The box is fitted using four screws and the power supply unit is connected to mains voltage as shown below. Fuse Connect mains voltage to the transformer ______________________________________________________________________________ Page 14 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
-
Page 15: Fitting A Dc-Dc Converter
DC-DC converter Order no.: EM-311-DK Installing the DC-DC converter: To connect the converter, see diagram on page 23. ______________________________________________________________________________ Page 15 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 16: Connection Of The Motor Control Unit
Error output. External relay, if any, connected – (gnd) Terminal 16: HOME. Actuators forced to return to starting position and system initialised. ______________________________________________________________________________ Page 16 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 17: Installing The Actuators
For additional information, please refer to the data sheet for the actuator in question. ______________________________________________________________________________ Page 17 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 18: Connection Of Linak Actuators
Instruction Manual for TECH-system type 239 Connection of LINAK actuators The majority of LINAK actuators are supplied as standard with a pre-fitted cable, and the actuators are also fitted with different types of plugs depending on which control box has been selected for the control operations. - Page 19 Motor cable Order no. 0237002-1500-A Hall A Hall B (Yellow) (Green) (Blue) (Brown) (Hall+) (Hall -) (Red) (Black) ______________________________________________________________________________ Page 19 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
-
Page 20: Connection Diagram For Linak Actuators
Actuator LA36 / LA37 w/Dual hall sensor • Column BL1 w/hall sensor • Actuator LA40 w/Dual hall sensor • Column LP2 w/reed switch • ______________________________________________________________________________ Page 20 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 21: La12/30 - Reed
Instruction Manual for TECH-system type 239 LA12/30 - Reed LA28/32– Reed LA31 – Reed ______________________________________________________________________________ Page 21 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 22: La14/25 - Hall
Instruction Manual for TECH-system type 239 LA14/25 – Hall LA20 – Hall LA23 – Hall ______________________________________________________________________________ Page 22 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 23: La35 - Hall
Instruction Manual for TECH-system type 239 LA35 – Hall LA36/37 – Hall BL1 – Hall ______________________________________________________________________________ Page 23 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 24: La20 - Dual Hall
Instruction Manual for TECH-system type 239 LA20 – Dual Hall LA23 – Dual Hall LA36/37 – Dual Hall ______________________________________________________________________________ Page 24 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 25: La40 - Dual Hall
White Terminal 11 + 12 13 = 1 Green Pos. Neg. 14 = 0 LA40 LP2.2 – Reed ______________________________________________________________________________ Page 25 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 26: Connection Diagram For Linak Control Devices
Instruction Manual for TECH-system type 239 Connection diagram for LINAK control devices (Max. Cable length = 5 m) ______________________________________________________________________________ Page 26 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 27: Connection Diagram For Plc And Manual Control Unit
(Cable length on the manual control unit above 5 m) Connection diagram for relais for Fault OUT on PLC Service run (Remark! Parameter 13 = 0) ______________________________________________________________________________ Page 27 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 28: Position Read Out Via Plc
Instruction Manual for TECH-system type 239 Position read out via PLC LA36 - Hall ______________________________________________________________________________ Page 28 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 29: Parameter Settings
<1 / 11>, which means parameter 1 of 11. The value is presented in square brackets [ ] and can be changed by pressing the plus or minus buttons. ______________________________________________________________________________ Page 29 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 30: Parameters
13. Dual pulse mode: Set utilisation of Dual hall pulse feedback. 14. End stop OUT: Set maximum stroke length, OUT. ______________________________________________________________________________ Page 30 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... - Page 31 LP2- LA30- LA31- LA32- LA35- LA14/23 DualHa Hall/D Hall/D /25-Hall Reed Reed Reed Reed Reed Reed Hall 100* ______________________________________________________________________________ Page 31 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
-
Page 32: Explanation Of Parameters
The following section presents a more detailed explanation of the individual parameters. Set the parameters by entering a number in the display. NB! LINAK´s recommended parameters are presented in { } after each description below. This parameter makes it possible to set the operating speed of Speed: the actuators. - Page 33 STOP command. The following options are available: 1 = continuous mode 2 = impulse mode 3 = impulse-2 mode ______________________________________________________________________________ Page 33 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
- Page 34 The value “0” indicates that the function is deactivated The following options are available: 0–32000 ______________________________________________________________________________ Page 34 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk...
-
Page 35: Turning On /Operation
• The system must not be used until it is incorporated into the end product. ______________________________________________________________________________ Page 35 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 36: Maintenance
Displays the current position, measured in pulses, for actuator 1 6. Position 2 Displays the current position, measured in pulses, for actuator 2 ______________________________________________________________________________ Page 36 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 37: Operation
WARNING! Make sure that the application will not be twisted or deformed if one of the actuators is not operating. ______________________________________________________________________________ Page 37 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 38: Troubleshooting
- Stop system and wait until it is cooled 5 flashes Overheating down Resetting errors All errors are reset when the actuators are restarted. ______________________________________________________________________________ Page 38 of 39 june 2020 ver. 09 LINAK Danmark A/S - Mønstedsvej 9 8600 Silkeborg - Telefon 86803611 - www.linak.dk... -
Page 39: Disposal Of Linak Products
Instruction Manual for TECH-system type 239 Disposal of LINAK products To dispose of LINAK products, start by sorting them into different categories for recycling or incineration. We recommend that you dismantle your product as fully as possible for disposal, and that you reuse the parts.
Need help?
Do you have a question about the 239 Series and is the answer not in the manual?
Questions and answers