Hach SC4500 User Instructions
  1. Manuals
  2. Brands
  3. Hach Manuals
  4. Controller
  5. SC4500
  6. User instructions

Hach SC4500 User Instructions

Hide thumbs Also See for SC4500:
Table of Contents

Advertisement

Quick Links

DOC273.52.90750
SC4500 network, HCNB
10/2021, Edition 1
User Instructions

Advertisement

Table of Contents
loading

Related Manuals for Hach SC4500

Summary of Contents for Hach SC4500

  • Page 1 DOC273.52.90750 SC4500 network, HCNB 10/2021, Edition 1 User Instructions...

  • Page 3: Table Of Contents

    2.1 LAN connection ....................5 2.2 WiFi network connection ..................6 2.3 Cellular network connection .................. 6 2.3.1 Configuration with Hach Cellular (Telenor) SIM ......... 7 2.3.2 Configuration with customer supplied SIM ..........7 Section 3 Hach Controller Network Bus configuration ......
  • Page 4 Table of Contents...

  • Page 5: Section 1 General Information

    Section 1 General information In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential damages resulting from any defect or omission in this manual. The manufacturer reserves the right to make changes in this manual and the products it describes at any time, without notice or obligation. Revised editions are found on the manufacturer’s website.

  • Page 6: Intended Use

    1.3 Product overview Use the Hach Controller Network Bus (HCNB) to make a network that is compatible with industrial Ethernet-based infrastructures and topologies for real-time data sharing. HCNB is a bi-directional communications protocol used to connect Claros controllers and RTC modules. There is no master hierarchy in HCNB.

  • Page 7: Lan Connection

    Figure 1 Controller Ethernet ports options 1 No Ethernet ports (LAN configuration: none) 5 LAN Ethernet connector (LAN configuration: mix IEP) 2 Digital SC connectors 6 Industrial Ethernet protocol connector (LAN configuration: mix IEP) 3 Controller 7 Industrial Ethernet protocol connectors (LAN configuration: IEP only) 4 LAN Ethernet connectors (LAN configuration: split or chaining)

  • Page 8: Wifi Network Connection

    Option Description Split One Ethernet port is configured for LAN connectivity and the other Ethernet port is configured for a separate LAN or Modbus TCP. When selected, the Lan port 1 configuration and Lan port 2 configuration settings show on the LAN menu. The two Ethernet ports have different port configurations.

  • Page 9: Configuration With Hach Cellular (Telenor) Sim

    2.3.1 Configuration with Hach Cellular (Telenor) SIM If the controller connects to the internet with the factory installed SIM card and the default Hach data plan (Telenor), do the steps that follow: 1. Push the main menu icon, then select Controller > Connectivity > Cellular.

  • Page 10: Hcnb Automatic Configuration

    • Set the HCNB button to on to enable HCNB functionality. 3. Push APPLY. When HCNB is set to on or off, the controller must be restarted. 3.1 HCNB automatic configuration HCNB uses the standard mDNS protocol to automatically find all of the controllers connected to the network segment.

  • Page 11: Hcnb-View Statistics

    2. Push the main menu icon, then select Controller > Connectivity > Claros. Set to on. 3. Add the controller to the user Claros account. On a web-enabled device open Claros and follow the instructions on the screen. Section 5 Network topologies The topologies that follow are applicable to the SC4500 network configuration. English 9...

  • Page 12: Hcnb Through A Customer Network (Lan Only)

    • Controller 3 connects to the HCNB through LAN and connects to a PLC through Industrial Ethernet protocols, Profibus DP or a mA output. 1 Controller 1, SC4500 4 PLC (refer to the documentation supplied with the controller, Profinet module and...
  • Page 13 f. Select Controller > Connectivity > HCNB > HCNB. Select On. Push OK to restart the controller. Note: Wait until the controller restarts. Do not touch the display or go to other menus or an error message will show. 2. Set the Controller 2 configuration the same as Controller 1. 3.

  • Page 14: Hcnb Through A Customer Network (Wired Chaining)

    • Controller 3 connects to the HCNB through LAN and connects to a PLC through Industrial Ethernet protocols, Profibus DP or a mA output. 1 Controller 1, SC4500 4 PLC (refer to the documentation supplied with the controller, PROFINET module and...
  • Page 15 g. Select Controller > Connectivity > HCNB > HCNB. Select On. Push OK to restart the controller. Note: Wait until the controller restarts. Do not touch the display or go to other menus or an error message will show. 2. Set the Controller 2 configuration as follows: a.

  • Page 16: Hcnb Through A Customer Network (Lan + Wifi)

    1 Wi-Fi USB box 5 PLC (refer to the documentation supplied with the controller, Profinet module and EtherNet/IP module to configure the PLC) 2 Controller 1, SC4500 6 IEP connection, Profibus DP, or 4-20 mA connection 3 Controller 2, SC4500...
  • Page 17 d. Select Controller > Connectivity > HCNB > Interface. Select Wi-Fi. e. Select Controller > Connectivity > Wi-Fi > Wi-Fi connectiviy. Select On. Refer to WiFi network connection on page 6 to configure the Wi-Fi connection. f. Select Controller > Connectivity > HCNB > HCNB. Select On. Push OK to restart the controller.

  • Page 18: Hcnb Through Embedded Lan Server (Not Claros Compatible)

    • Controller 3 connects to the HCNB through LAN and connects to a PLC through Industrial Ethernet protocols, Profibus DP or a mA output. 1 Controller 1, SC4500 4 PLC (refer to the documentation supplied with the controller, PROFINET module and...
  • Page 19 d. Select Controller > Connectivity > HCNB > Auto detection. Select On. e. Select Controller > Connectivity > HCNB > HCNB. Select On. Push OK to restart the controller. Note: Wait until the controller restarts. Do not touch the display or go to other menus or an error message will show.

  • Page 20: Claros And Hcnb Through Cellular Connection With Internet Sharing

    • Controller 3 connects to Claros and HCNB though a LAN and connects to a PLC through Industrial Ethernet protocols, Profibus DP or a mA output. 1 Cellular USB box 4 Controller 3, SC4500 2 Controller 1, SC4500 5 PLC (refer to the documentation supplied...
  • Page 21 h. Select Controller > Connectivity > HCNB > HCNB. Select On. Push OK to restart the controller. Note: Wait until the controller restarts. Do not touch the display or go to other menus or an error message will show. 2. Set the Controller 2 configuration as follows: a.
  • Page 22 20 English...
  • Page 24 Tel. +49 (0) 2 11 52 88-320 SWITZERLAND Fax (970) 669-2932 Fax +49 (0) 2 11 52 88-210 Tel. +41 22 594 6400 orders@hach.com info-de@hach.com Fax +41 22 594 6499 www.hach.com www.de.hach.com © Hach Company/Hach Lange GmbH, 2021. All rights reserved.

Table of Contents