Telit Wireless Solutions SE868SY-D EVK User Manual
Evaluation kit
Hide thumbs
Also See for SE868SY-D EVK:
- Hardware design manual (47 pages) ,
- Design manual (46 pages) ,
- Hw design manual (44 pages)
Subscribe to Our Youtube Channel
Related Manuals for Telit Wireless Solutions SE868SY-D EVK
Summary of Contents for Telit Wireless Solutions SE868SY-D EVK
- Page 1 SE868SY-D EVK User Guide 1VV0301700 Rev. 1 – 2021-10-01 Telit Technical Documentation...
-
Page 2: Applicability Table
SE868SY-D EVK User Guide APPLICABILITY TABLE PRODUCTS SE868SY-D EVK 1VV0301700 Rev.1 Page 2 of 30 2021-10-01 Not Subject to NDA... -
Page 3: Table Of Contents
Related Documents GENERAL PRODUCT DESCRIPTION 2.1. Overview EVALUATION KIT DESCRIPTION Content of the Evaluation Kit EVK Versions Board Appearance SE868SY-D EVK LAYOUT AND SCHEMATICS Layout Schematics GETTING STARTED Supplying the EVK Selecting the Host Interface Reset Testing the Receiver LEGACY EVK RELEASE... - Page 4 SE868SY-D EVK User Guide 6.4.3. Legacy Board - Testing the Receiver Differences between Legacy and New Release FIRMWARE UPGRADE Flashing Requirements Flashing Instructions Copyrights and Other Notices 7.3.1. Copyrights 7.3.2. Computer Software Copyrights Usage and Disclosure Restrictions 7.4.1. License Agreements 7.4.2.
-
Page 5: Introduction
SE868SY-D EVK User Guide 1.. INTRODUCTION Scope Aim of this manual is to provide information on the Evaluation Kit (EVK) for the SE868SY- D module. Audience This document is intended for customers evaluating the SE868SY-D module’s performances. Contact Information, Support... -
Page 6: Symbol Conventions
SE868SY-D EVK User Guide Symbol Conventions Danger: This information MUST be followed, or catastrophic equipment failure or personal injury may occur. Warning: Alerts the user on important steps about the module integration. Note/Tip: Provides advice and suggestions that may be useful when integrating the module. -
Page 7: General Product Description
SE868SY-D EVK User Guide 2.. GENERAL PRODUCT DESCRIPTION Overview The SE868SY-D Evaluation Kit (EVK) allows the customer to test the functionalities of the SE868SY-D module. Note: Please note that this document is provided for marketing purposes only. Since the SE868SY-D is under development at the time of this writing, some of the features listed herein might be subject to change in the final product. -
Page 8: Evaluation Kit Description
SE868SY-D EVK User Guide 3.. EVALUATION KIT DESCRIPTION Content of the Evaluation Kit The SE868SY-D Evaluation Kit is provided in the following package: • An SE868SY-D EVK board • A USB-A/Mini-USB cable • A dual-band, L1+L5 active antenna The kit is complemented by TelitView, a GNSS evaluation software tool, available through Telit technical support or on the Download Zone portal on the Telit website. -
Page 9: Se868Sy-D Evk Layout And Schematics
SE868SY-D EVK User Guide 4.. SE868SY-D EVK LAYOUT AND SCHEMATICS Layout Figure 2: SE868SY-D EVK layout, also detailing the default jumper configuration 1VV0301700 Rev.1 Page 9 of 30 2021-10-01 Not Subject to NDA... - Page 10 SE868SY-D EVK User Guide The user interface elements (LEDs, switches, and connectors) that can be managed by the customers to configure the SE868SY-D EVK are listed in Table 2 Reference Designator Description DL100 LED- Module ON DL101 LED – Tx Data DL102 LED –...
-
Page 11: Schematics
SE868SY-D EVK User Guide Schematics Schematics are available on Telit Download Zone webpage 1VV0301700 Rev.1 Page 11 of 30 2021-10-01 Not Subject to NDA... -
Page 12: Getting Started
SE868SY-D EVK User Guide 5.. GETTING STARTED Supplying the EVK The EVK is powered by the USB cable: the input 5V is then regulated in four different stable voltages: • 1.8V to supply the SE868SY-D module. • 1.8V to supply the EVK auxiliary circuitry. -
Page 13: Reset
SE868SY-D EVK User Guide PL116 (HIF_SEL_1) PL112 (HIF_SEL_0) Selected host interface JUMPER unpopulated HIF_SPI Table 3: Host Interface selection Warning: Do not pull up both HIF_SEL_0 and HIF_SEL_1 at the same time: this configuration is reserved Note: Current consumption will slightly increase when one of the external pull ups on HIF_SEL_x is enabled. -
Page 14: Legacy Evk Release
SE868SY-D EVK User Guide 6.. LEGACY EVK RELEASE Legacy Board Appearance The legacy EVK is provided with the default jumper configuration, as shown in Figure 3 Figure 3 SE868SY-D EVB-LEGACY 1VV0301700 Rev.1 Page 14 of 30 2021-10-01 Not Subject to NDA... -
Page 15: Legacy Evk Layout
SE868SY-D EVK User Guide Legacy EVK LAYOUT Figure 4: Legacy SE868SY-D EVK Layout, also detailing the default jumper configuration. 1VV0301700 Rev.1 Page 15 of 30 2021-10-01 Not Subject to NDA... -
Page 16: Legacy Evk Schematics
SE868SY-D EVK User Guide The user interface elements (LEDs, switches, and connectors) that can be managed by the customers to configure the SE868SY-D EVK are listed in Table 4 Reference Designator Description DL101 LED – Tx Data DL102 LED – 1 PPS S0100 SMA connector –... -
Page 17: Getting Started - Legacy Board
SE868SY-D EVK User Guide Getting Started – Legacy Board 6.4.1. Supplying the Legacy EVK The EVK is powered from the USB cable: the input 5V is then regulated into three stable voltages: • 1.8V to supply the SE868SY-D module. •... -
Page 18: Legacy Board - Testing The Receiver
SE868SY-D EVK User Guide Jumpers on PL107 and PL115 are not required as they would just add a second pull-down resistor in parallel to the internal one. 6.4.3. Legacy Board - Testing the Receiver To test the RF performances of the SE868SY-D, a dual band L1+L5 antenna shall be connected to SO100. - Page 19 SE868SY-D EVK User Guide cs1669d - old EVK version cs1669e- new EVK version In Error! Reference source not found., the differences between the old and the new EVK are highlighted. All differences are identified in Table 6 and details are provided per each.
- Page 20 EVK in concurrence with other wireless technologies without the addition of any other external filter Table 6: Main differences between the new and the legacy SE868SY-D EVK 1VV0301700 Rev.1 Page 20 of 30 2021-10-01...
-
Page 21: Firmware Upgrade
SE868SY-D EVK User Guide 7.. FIRMWARE UPGRADE Flashing Requirements • Personal Computer with MS Windows OS and a USB port; • Telit CXD5610 Firmware Programmer – Command line tool; • Firmware file, i.e.: o Binary - V50_100_N115_E104_B09.bin; Flashing Instructions The SE868SY-D can be programmed via command line by using the Telit CXD5610 Firmware Programmer whose command line syntax is reported below: Telit_CXD5610_Firmware_Programmer.exe <port>... - Page 22 SE868SY-D EVK User Guide When a reset is requested by the application to set the SE868SY-D in boot mode, a reset or power-cycle must be performed by pressing the switch SW102 (cs1669e) or removing and then reinstalling the jumper on PL102 (cs1669d and cs1669e).
-
Page 23: Copyrights And Other Notices
SE868SY-D EVK User Guide Figure 8: Firmware and tool on the same folder Warning: Flow control usage is recommended for baud rates between 460800 bps and 921600 bps while it is mandatory for higher baud rates. PRODUCT AND SAFETY INFORMATION... -
Page 24: Copyrights
SE868SY-D EVK User Guide 7.3.1. Copyrights This instruction manual and the Telit products described herein may include or describe Telit copyrighted material, such as computer programs stored in semiconductor memories or other media. The laws in Italy and in other countries reserve to Telit and its... -
Page 25: Copyrighted Materials
SE868SY-D EVK User Guide 7.4.2. Copyrighted Materials The Software and the documentation are copyrighted materials. Making unauthorized copies is prohibited by the law. The software or the documentation shall not be reproduced, transmitted, transcribed, even partially, nor stored in a retrieval system, nor translated into any language or computer language, in any form or by any means, without prior written permission of Telit. -
Page 26: Waiwer Of Liability
SE868SY-D EVK User Guide WAY OUT OF THE USE OR DISTRIBUTION OF THE OTHER CODES OR THE EXERCISE OF ANY RIGHTS GRANTED UNDER EITHER OR BOTH THIS LICENSE AND THE LEGAL TERMS APPLICABLE TO ANY SEPARATE FILES, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. - Page 27 SE868SY-D EVK User Guide network or external devices or having an impact on the security system. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna must be installed carefully to avoid any interference with other electronic devices and must guarantee a minimum distance from the body (20 cm).
-
Page 28: Acronyms Glossary
SE868SY-D EVK User Guide 8.. ACRONYMS GLOSSARY GNSS Global Navigation Satellite System Global Positioning System Evaluation Kit Host Interface for the SE868SY-D module UART Universal Asynchronous Receiver/Transmitter 1VV0301700 Rev.1 Page 28 of 30 2021-10-01 Not Subject to NDA... -
Page 29: Document History
SE868SY-D EVK User Guide 9.. DOCUMENT HISTORY Revision Date Changes 2021-10-01 Minor changes on the language Minor changes on the layout Legal Notices updated Added new EVB description and Legacy section Added Firmware upgrade section 2020-12-23 First issue From Mod.0818 rev.4 1VV0301700 Rev.1...
Need help?
Do you have a question about the SE868SY-D EVK and is the answer not in the manual?
Questions and answers