Raider RD-GBC23 Manual page 16

30 www.raider.bg
4. Starting the engine.
Switch the ignition key in the starting position. If the engine is cold or ambient temperature is low,
set the choke control in the choke position. After starting the engine, wait a while until the engine
warms up gradually and go back choke control. A sure sign of the need to go back choke control is
the appearance of thick smoke from the tailpipe.
NOTE: The choke control does not close when you start the heated engine or at relatively high
temperature environment. Under these conditions, no pull choke control when you start the engine.
4.1. Switch the ignition key in the starting position I.
4.2. Set the choke control in the choke position, if the ambient temperature is low.
4.3. At the start of the engine is likely to be obtained kick from the recoil starter. So take your
proper and stable position when pulling the hand launcher.
4.4. Gently pull hand starter, making it convenient to grasp the handle until you feel resistance.
Then pull sharply.
4.5. WARNING! Do not let the starter rope to be wound back sharply in the engine. Return it gently
to avoid damage to the starter.
4.6. After starting the engine to increase the speed with a throttle lever.
5. Working with brush cutter.
5.1. Always keep the machine with both hands.
5.2. The grass is cut down with a sideways, lateral movement.
5.3. The movement from right to left is the clearing stroke and the movement from left to right is
the return stroke.
5.4. Try to work rhythmically. Stand firmly with your feet apart.
5.5. Move forward after the return stroke and stand firmly again.
5.6. By clearing stroke stand firmly again.
5.7. Avoid the previously cut material during the return stroke. Always work at full throttle. This
reduces the risk of material wrapping around the blade.
5.8. Do not operate without mounted safety guard (6).
5.9. Never use the brush cutter higher than 76 cm above the ground.
6. Stop the engine. Reduce the engine speed with a throttle lever. Allow the engine to run about
30 seconds, then stop the engine by switching off the ignition key 0 (Stop).
Always collect the grass clippings after you stop the engine and wait to stop the rotation of the
blade.
7. Maintenance. Periodic checks are needed and settings to keep the brush cutter in optimal
performance. Regular maintenance will prolong the life in.
WARNING! Before any maintenance work on brush cutter engine must be off!
7.1. The inspection and maintenance must be performed by authorized persons, unless you have
the appropriate tools and skills necessary to do so.
Please note that support is recommended under normal operating conditions. If using a brush
cutter under other circumstances, we recommend you consult your dealer.
7.2. Turn off the engine and remove spark plug cable before examination.
7.3. Let the engine and manifold to cool so as not to burn from the hot surfaces.
7.4. Wear protective gloves so not to cut of the sharp elements.
7.5. Clean grass stuck to the blade and smear it with grease.
7.6. Drain all fuel from the engine, where to store motor mowers for more than a month.
7.7. The items listed below must be an experienced professional service it if you do not have the
appropriate tools and training.
7.8. You should always vent to cool the engine to be clean and free. They are open on the side
of the launcher.
The contents of the table, shows the periods in which the planned maintenance work to be done.
Chart support for the brush cutter
Period
Each time before
Once per month
starting the
or after 12 hours
gasoline brush
Element
of work
cutter
to check
●
Check the air
filter
●
Clean the air filter
Check the spark
Replace the
gasoline hose
7.9. Cleaning the air filter.
Do not use a brush cutter with dirty air filter or without air filter. The dust and small particles that
will suck the engine will shorten its operational life.
Remove the air filter. Clean the filter with solvent and allow to dry completely after cleaning. Do
not clean the air filter with flammable liquids, may occur because of fire or explosion under certain
conditions. Once you clean it, put the air filter back into place.
7.10. Keeping the spark plug.
The recommended type of spark plug is Champion RCJ7Y, NGK BPMR7A or NHSP LD L8RTF.
To ensure normal operation of the engine, the spark plug must have adequate distance between the
electrodes and must be cleaned of deposits. Remove the "pipe" of the spark plug, and pull the handle
on the top and end. Under no circumstances remove "pipe" by pulling the cord. Tailpipe can be very
Once per month Once per month Once per month
or after 50 hours of after 100 hours of after 300 hours
of work of work of work
●
Each two years
31