Page 2
A copy of this limited warranty can also be obtained by written request to Federal Signal Corporation, 2645 Federal Signal Drive, University Park, IL 60484, email to info@fedsig.com or call +1 708-534-3400.
Contents Safety Message to Installers and Service Personnel .....4 Overview.....................7 Unpacking ..................7 Installation ..................8 Wiring ....................10 Permanently Mounting ..............11 Pipe Mounting ..................13 Using Magnetic Mounting ..............13 Setting up the Controller ..............14 Operation ..................17 Cleaning ...................18 Getting Technical Support ..............18 Getting Repair Service ..............19 Ordering Replacement Parts ............19 Returning a Product to Federal Signal ..........19 Figures...
• Never attempt to install aftermarket equipment that connects to the vehicle wiring without reviewing a vehicle wiring diagram available from the vehicle manufacturer. Ensure that your installation will not affect vehicle operation or mandated Search Light NightSpire ™ Federal Signal www.fedsig.com...
Page 5
Safety Message to Installers and Service Personnel safety functions or circuits. Always check the vehicle for proper operation after installation. • The lighting system components, especially the outer housing, get hot during operation. Be sure to disconnect power to the system and allow the system to cool down before handling any components of the system.
Page 6
• File these instructions in a safe place and refer to them when maintaining and/or reinstalling the product. Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death. Search Light NightSpire ™ Federal Signal www.fedsig.com...
Unpacking Overview The NightSpire is a remotely adjustable search light with ™ an adjustable light pattern. It can be rotated horizontally, 360° continuously. It can elevate from 40° down to 90° up. The light output is continuously adjustable from a 4° spot to a 50°...
To attach the mounting flange: 1. Locate the detent on the search light and one of the two detent notches on the flange. 2. Align the search light as shown in Figure 1. Search Light NightSpire ™ Federal Signal www.fedsig.com...
Installation Figure 1 Search light mounted on flange 3. Push the search light down completely and turn clockwise 1/8 turn until the detent locks in place. To remove the search light from the flange: 1. Use a flat-tipped screwdriver to push the detent while turning the search light counterclockwise.
2. Install a 5 A fuse and fuse holder to the positive (+) terminal at the voltage source. Connect one side of the power switch to this fuse. Connect the light’s red wire to the switched terminal of the switch. Search Light NightSpire ™ Federal Signal www.fedsig.com...
Permanently Mounting 3. Connect the black (–) wire from the search light to a known good vehicle ground as close to the unit as is practical. Permanently Mounting To permanently mount the search light: 1. Scribe the locations of the three mounting holes on the mounting surface using the desired mounting holes in the flange or base as a guide.
5. Align the search light over the drilled holes. Route the wires through the wire routing hole. Seal the hole with a bushing or RTV if entering a watertight compartment. Figure 4 Exploded view of installation Search Light NightSpire ™ Federal Signal www.fedsig.com...
Using Magnetic Mounting 6. Secure the base to the mounting surface with the selected panhead screws. Pipe Mounting The base was designed for the optional installation onto the end of a threaded 1-inch NPT pipe. The supply wires are to run within the pipe for protection.
1. Open the battery compartment by removing the #1 Phillips head screw and removing the cover. 2. Install two AAA batteries in the orientation indicated in the battery compartment. 3. Replace the cover and secure with the screw. Search Light NightSpire ™ Federal Signal www.fedsig.com...
Page 15
To pair the unit: 1. With the NightSpire powered down, hold the desired Preset button for five seconds to begin the pairing procedure. 2. When the button begins to flash blue, apply power to the search light.
Setting up the Controller Figure 5 Controller Directional Buttons Directional Spot in/ Buttons Spot out Memory Power Presets 1, 2, 3 Search Light NightSpire ™ Federal Signal www.fedsig.com...
Operation Operation LIGHT HAZARD: This product contains a high intensity LED device. To prevent permanent eye damage, DO NOT stare into the light beam at close range. When the search light is powered on, it will perform a calibration procedure. It will rotate to zero and return to the last position it was at when powered off.
Failure to follow this precaution can cause crazing or cracking of the lens/dome and voids the warranty claims for the light. Getting Technical Support For technical support, please contact: Federal Signal Corporation Service Department Phone: 1-800-433-9132 Email: empserviceinfo@fedsig.com Search Light NightSpire ™...
(RMA). Obtain a RMA from a local Distributor or Manufacturer’s Representative. Provide a brief explanation of the service requested, or the nature of the malfunction. Address all communications and shipments to the following: Federal Signal Corporation Service Department 2645 Federal Signal Dr. University Park, IL 60484-3167...
Page 20
2645 Federal Signal Drive University Park, Illinois 60484 www.fedsig.com Customer Support Police/Fire-EMS: 800-264-3578 • +1 708 534-3400 Work Truck: 800-824-0254 • +1 708 534-3400 Technical Support 800-433-9132 • +1 708 534-3400...
Page 22
2645 Federal Signal Drive University Park, Illinois 60484 www.fedsig.com Atención al Cliente Policía/Bomberos-SMU: 800-264-3578 • +1 708 534-3400 Camionetas: 800-824-0254 • +1 708 534-3400 Soporte técnico 800-433-9132 • +1 708 534-3400 Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 23
Returning a Product to Federal Signal Índice Mensajes de seguridad para los instaladores y el personal de servicio ..................24 Descripción ..................27 Desembalaje..................27 Instalación ..................28 Cableado ..................30 Montaje permanente................31 Montaje de tubo ................33 Uso del montaje magnético ............33 Preparación del control remoto .............34 Funcionamiento ................37 Limpieza ...................38 Obtención de soporte técnico ............38...
Page 24
Jamás intente instalar accesorios automotrices que se conecten al cableado del vehículo sin antes revisar el diagrama de cableado del vehículo de su fabricante. Asegúrese de que la instalación no afectará el funcionamiento del vehículo ni los Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 25
Mensajes de seguridad circuitos o las funciones de seguridad obligatorios. Después de una instalación, compruebe siempre que el vehículo funcione correctamente. • Los componentes del sistema de iluminación, en especial la carcasa externa, se calientan durante su funcionamiento. Asegúrese de desconectar la corriente eléctrica que alimenta el sistema y déjelo enfriar antes de manipular cualquiera de sus componentes.
Page 26
Conserve estas instrucciones en un lugar seguro y consúltelas cuando realice tareas de mantenimiento o vuelva a instalar el producto. El incumplimiento de todas estas precauciones e instrucciones de seguridad puede causar daños materiales, lesiones graves o incluso la muerte. Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 27
Desembalaje Descripción NightSpire es una luz de búsqueda con un patrón de luz ™ ajustable que se puede ajustar en forma remota. Se puede girar horizontalmente, 360° continuos. Se puede cambiar de elevación de 40° hacia abajo a 90° hacia arriba. La salida de luz se puede ajustar en forma continua desde un punto de 4°...
Page 28
Localice el retén en la luz de búsqueda y una de las dos muescas de retención en la brida. 2. Alinee la luz de búsqueda como se muestra en la Figura 1. Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 29
Instalación Figura 1 Luz de búsqueda montada en la brida 3. Presione la luz de búsqueda completamente hacia abajo y gírela en el sentido de las agujas del reloj 1/8 de vuelta, hasta que el retén se trabe. Para quitar la luz de búsqueda de la brida: Use un destornillador de punta plana para presionar el retén mientras gira la luz de búsqueda en el sentido contrario a las agujas del reloj.
Page 30
2. Instale un fusible de 5 A y un portafusibles al terminal positivo (+) de la fuente de voltaje. Conecte un extremo del interruptor de corriente eléctrica a ese fusible. Conecte el cable rojo de la luz al terminal conmutado del interruptor. Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 31
Montaje permanente 3. Conecte el cable negro (–) desde la luz de búsqueda hasta una descarga a tierra en el vehículo que sea buena, conocida y lo más cercana a la unidad como sea viable. Montaje permanente Para montar permanentemente la luz de búsqueda: Marque la ubicación de los tres orificios de montaje sobre la superficie de montaje utilizando como guía los orificios de montaje deseados en la brida o la base.
Page 32
Selle el orificio con un cojinete o vulcanizado a temperatura ambiente si ingresa en un compartimiento impermeable. Figura 4 Vista de despiece de la instalación Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 33
Uso del montaje magnético 6. Sujete la base a la superficie de montaje con los tornillos de cabeza redonda seleccionados. Montaje de tubo La base fue diseñada para su instalación óptima en el extremo de un tubo NPT roscado de 1 pulgada. Los cables de alimentación se pasan por el interior del tubo para protegerlos.
Page 34
Abra el compartimiento para pilas quitando el tornillo Phillips n.º 1 y la cubierta. 2. Coloque dos pilas AAA en la orientación indicada en el compartimiento para pilas. 3. Vuelva a colocar la cubierta y asegure con el tornillo. Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 35
Para emparejar la unidad: Con la luz de búsqueda NightSpire apagada, mantenga presionado el botón de preselección que desee durante cinco segundos para comenzar el procedimiento de emparejamiento.
Page 36
Preparación del control remoto Figura 5 Control remoto Botones de dirección Botones de Punto angosto/ dirección Punto ancho Memoria Encendido Preselecciones 1, 2, 3 Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 37
Funcionamiento Funcionamiento ADVERTENCIA PELIGRO LUMÍNICO: Este producto contiene un dispositivo LED de alta intensidad. Para evitar daños permanentes a la vista, NO mire directamente la luz a poca distancia. Cuando se encienda, la luz de búsqueda realizará un procedimiento de calibración. Girará hasta cero y volverá a la última posición en la que estaba cuando se apagó.
Page 38
Obtención de soporte técnico Para obtener soporte técnico, comuníquese con: Federal Signal Corporation Departamento de Servicio Teléfono: 1-800-433-9132 Correo electrónico: empserviceinfo@fedsig.com Luz de búsqueda NightSpire ™ Federal Signal www.fedsig.com...
Page 39
Brinde una explicación breve sobre el servicio solicitado o la naturaleza de la falla. Dirija todas las comunicaciones y los envíos a: Federal Signal Corporation Departamento de Servicio 2645 Federal Signal Dr. University Park, IL 60484-3167 Pedido de piezas de repuesto Para pedir piezas de repuesto, comuníquese con Atención al Cliente...
Page 40
2645 Federal Signal Drive University Park, Illinois 60484 www.fedsig.com Atención al Cliente Policía/Bomberos-SMU: 800-264-3578 • +1 708 534-3400 Camionetas: 800-824-0254 • +1 708 534-3400 Soporte técnico 800-433-9132 • +1 708 534-3400...
Need help?
Do you have a question about the NightSpire and is the answer not in the manual?
Questions and answers