Meat Thermometer - Siemens HB478G5.6 User Manual And Installation Instructions

en Meat thermometer
9.5 Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement: The function selector must be set to the
"Off" position ⁠ .
Use the or button to set the time.
1.
Press the button.
2.
a The time that is set appears on the display.
10

Meat thermometer

Cook with precision by inserting the meat probe into
the food and setting a core temperature on the appli-
ance. Once the set core temperature has been
reached in the food, the appliance stops automatically.
10.1 Suitable types of heating with the meat
thermometer
Only certain types of heating are suitable for use with
the meat thermometer.
Suitable heating functions include:
¡ 3D hot air
¡ Hot air gentle
¡ Pizza setting
¡ Hot air grilling
¡ Top/bottom heating
Note: If the meat thermometer is being used and you
select an unsuitable type of heating, a signal sounds.
10.2 Inserting the meat thermometer
Use the meat thermometer supplied or order a suitable
meat thermometer from our after-sales service.
WARNING ‒ Risk of electric shock!
Using the wrong meat probe could damage the insula-
tion.
Only use the meat probe for this specific appliance.
▶
ATTENTION!
Otherwise the meat probe may be damaged.
Do not trap the cable of the meat probe.
▶
To prevent the meat probe from being damaged by
▶
excessive heat, there must be a gap of a few centi-
metres between the grill element and the meat
probe. The meat may expand during the cooking
process.
Insert the meat thermometer at an angle into the
1.
thickest part of the meat.
Ensure that the tip of the meat thermometer is
correctly positioned in the meat:
– The tip must be roughly in the middle of the
food.
– The tip must not be inserted in the fat.
– The tip must not touch any cookware or bones.
Place the food with the meat thermometer into the
2.
cooking compartment.
14
Tip: You can go to the "basic settings" → Page 18 to
specify whether or not the time should be shown on
the display.
Changing the time on the clock
You can change the time on the clock at any time.
Requirement: The function selector must be set to the
"Off" position ⁠ .
Press the button repeatedly until
1.
in the display.
Use the or button to change the time.
2.
a The appliance applies the change after a few
seconds.
It is best to place the food in cookware into the
centre of the wire rack.
Plug the meat thermometer into the socket on the
3.
left-hand side of the cooking compartment.
Notes
¡ If you remove the meat thermometer while the food
is cooking, all the settings will be reset.
¡ Do not remove the meat thermometer when turning
the food. Once you have turned the food, check that
the meat thermometer is correctly positioned in the
food.
10.3 Setting the meat probe
The meat probe measures the temperature inside the
food between 30 °C and 99 °C.
Requirements
¡ The food with the meat probe is in the cooking com-
partment.
¡ The meat probe is plugged in inside the cooking
compartment.
Use the function selector to set a suitable type of
1.
heating.
lights up in the display and the core temperature
a
display appears next to the temperature of the cook-
ing compartment.
Use the or button to set the core temperature.
2.
The current core temperature of the food is shown
on the left, while the set core temperature is shown
on the right, e.g. 15 °C|75 °C.
Note: The current core temperature only appears
once it reaches 10 °C.
Use the temperature selector to set the temperature
3.
of the cooking compartment.
Set the cooking compartment temperature at least
10 °C higher than the core temperature.
Do not set the cooking compartment temperature to
higher than 250 °C.
a The appliance starts heating after a few seconds.
a Once the food reaches the core temperature, an
audible signal sounds and, in the display, the cur-
rent core temperature is equal to the set core tem-
perature, e.g. 75 °C|75 °C.
is highlighted