Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for True FS-51
Summary of Contents for True FS-51
- Page 1 FS-51 RESS SSEMBLY ANUAL Model: FS51 Rev: 030220...
- Page 2 TRUE experience. Innovation across the full product line has made TRUE successful and is a trademark of the TRUE heritage. TRUE’s patented Heart Rate Control technology is just one of the remarkable ways we deliver simple and superior performance every user can enjoy, and most importantly, use to achieve personal health and fitness goals.
-
Page 3: Table Of Contents
ABLE ONTENTS ........................4 AFETY ................ENERAL ARE AND AINTENANCE ................... 8 IMENSIONS AND EIGHT ......................9 REPARATION .................... 10 ARTON ONTENTS .................... 11 ARTON ONTENTS & A NSTALLATION SSEMBLY 1: I ............12 NSTALL THE RESS ABLE 2: A ............. -
Page 4: Safety
9. If the machine appears damaged or inoperable, contact a facility staff member to place an “OUT OF ORDER, DO NOT USE” sign on the machine until it is repaired. Only use TRUE supplied replacement components to service this machine. - Page 5 3. Install this piece of equipment on a solid level surface that does not deviate more then 1/8” over a 10’ distance (or as defined and required by local building and architectural codes. 4. TRUE strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability.
- Page 6 • Frames and Lifting Arms: Inspect weekly for integrity and function. Replace any component at first signs of wear. Use only TRUE supplied components. 4. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from TRUE free of charge.
-
Page 7: Eneral Are And Dimensions And Weight
Be sure all hardware is tight before using the machine. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your TRUE dealer or TRUE Fitness Corp. at (800) 883-8783 or service@truefitness.com. - Page 8 IMENSIONS AND EIGHT “I ” M ACHINE IMENSIONS 81.5” (207.0 cm) Machine Height: 64.4” (163.5 cm) Maximum user weight: 300 lbs. (136 KG) ACHINE EIGHT AND LOOR OADING EIGHT TACK ONFIGURATION ACHINE WEIGHT PPROXIMATE LOOR OADING 170 lbs. 469 LBS [213 KG] 56 LBS/FT [273 KG/M 250 lbs.
-
Page 9: Preparation
REPARATION EQUIRED OOLS Ratchet Wrench and Sockets: 9/16” Wrenches: 1/2”, 9/16”, 3/4”. (or an adjustable crescent wrench). Rubber Mallet Allen wrenches: (included with the machine) Hardware Measurement Guide: BHCS - BUTTON HEAD CAP SCREW SHCS - SOCKET HEAD CAP SCREW FHCS - FLAT HEAD CAP SCREW HHCS - HEX HEAD CAP SCREW MEASURE BOLT... -
Page 10: Box 1 Carton Contents
FS-51 B ARTON ONTENTS QTY. ESCRIPTION FS-CAP-000X TOP UPRIGHT CAP FS-GRD-200X GUIDE ROD FS-SHD-250X REAR SHROUD FS51-SHD-200X FRONT SHROUD FS51-UPR-000X UPRIGHT FRAME FS-BKT-000 GUIDE ROD BRACKET FS-WSB-000 WEIGHT STACK BASE FS51-PAD-100X SEAT PAD, FS-51 FS-PAD-000X BACK PAD... -
Page 11: Box 2 Carton Contents
FS 51 B ARTON ONTENTS QTY. ESCRIPTION FS51-MFR-000X MAINFRAME ASSY FS51-MFR-100X HANDLE, RIGHT FS51-MFR-200X HANDLE, LEFT FS51-MFR-300X REAR BRACE FS51-MFR-400X FOOT PLATE FS51-MFR-500X CONNECTION BRACE FS51-HWR-000X FL-51 HARDWARE BOX FS-SBR-000X SELECTOR BAR... -
Page 12: Tep Nstall The
1: I NSTALL THE RESS ABLE 1. Place the Leg Press frame squarely QTY. ESCRIPTION on the floor. C-450 SCREW, 3/8”-16 X 2-1/2” C-453 SCREW, 3/8”-16 X 2” 2. Route the cable as shown, installing C-683 SHOULDER SCREW, 3/8” X 1-1/2” the associated pulleys and hardware C-754C FLAT WASHER, 3/8”... -
Page 13: Connecting Brace
2: A SSEMBLE THE ONNECTING RACE 1. Route the cable through the QTY. ESCRIPTION attachment piece as shown. C-955A BASE, BOLT COVER, 3/8 FS51-MFR-500X CONNECTION BRACE 2. Loosely assemble ALL hardware C-445 SCREW, 3/8”-16 X 1” and the pulley shown in this step. C-448 SCREW, 3/8”-16 X 1-3/4”... -
Page 14: Upright Frame
3: A SSEMBLE THE PRIGHT RAME QTY. 1. Place the upright frame squarely on ESCRIPTION C-955A BASE, BOLT COVER, 3/8” the floor as shown. FS51-UPR-000X UPRIGHT FRAME 2. Assemble the rubber feet on both C-445 SCREW, 3/8”-16 X 1” the upright and Leg Press frame. S-550 RUBBER FOOT 3. -
Page 15: Rear Brace
4: I NSTALL THE RACE QTY. 1. Position the rear brace as shown. ESCRIPTION C-955A BASE, BOLT COVER, 3/8” 2. Loosely assemble ALL hardware FS51-MFR-300X REAR BRACE shown in this step. C-455 SCREW, 3/8”-16 X 4” 3. After aligning all component edges C-445 SCREW, 3/8”-16 X 1”... -
Page 16: Foot Plate
5: A SSEMBLE THE LATE 1. Position the foot plate as shown. QTY. ESCRIPTION C-766A LOCKNUT, 3/8”-16 2. Loosely assemble ALL hardware C-955A BASE, BOLT COVER, 3/8” shown in this step. FS51-MFR-400X FOOT PLATE 3. After aligning all component edges C-444 SCREW, 3/8”-16 X 3/4”... -
Page 17: Andles
6: A SSEMBLE THE ANDLES QTY. ESCRIPTION 1. Position the handles as shown. C-766A LOCKNUT, 3/8”-16 2. Loosely assemble ALL hardware C-955A BASE, BOLT COVER, 3/8” shown in this step. FS51-MFR-100X HANDLE, RIGHT 3. Do NOT tighten the hardware after FS51-MFR-200X HANDLE, LEFT installation. -
Page 18: Seat Pad
7: A SSEMBLE THE 1. Position the seat pad as shown. QTY. ESCRIPTION C-955A BASE, BOLT COVER, 3/8” 2. Loosely assemble ALL hardware FL51-PAD-100X SEAT PAD shown in this step. C-446 SCREW, 3/8”-16 X 1-1/4” 3. After aligning all component edges C-451 SCREW, 3/8”-16 X 2-3/4”... -
Page 19: Back Pad
8: A SSEMBLE THE QTY. ESCRIPTION 1. Position the seat pad as shown. C-955A BASE, BOLT COVER, 3/8” 2. Loosely assemble ALL hardware FS-PAD-000X BACK PAD shown in this step. C-451 SCREW, 3/8”-16 X 2-3/4” C-754C FLAT WASHER, 3/8” 3. After aligning all component edges C-749 LOCKWASHER, 3/8”... -
Page 20: Upright Pulleys
9: I NSTALL THE PRIGHT ULLEYS QTY. ESCRIPTION 1. Route the cable as shown, installing C-766A LOCKNUT, 3/8”-16 the associated pulleys and hardware B-900 4-1/2” PULLEY as you go along. C-448 SCREW, 3/8”-16 X 1-3/4” 2. Tighten ALL the hardware. C-754C FLAT WASHER, 3/8”... -
Page 21: Weight Stack
10: A SSEMBLE THE EIGHT TACK 1. Route the Low Pulley cable as shown. QTY. ESCRIPTION FS-GRD-200X ASSY, GUIDE ROD 2. Install the pulleys and associated C-445 SCREW, 3/8”-16 X 1” hardware as you go along. D 840 COLLAR, CLAMPING 1” ID 3. -
Page 22: Front Shroud
11: I NSTALL THE RONT HROUD 1. Place the front shroud on the upright QTY. ESCRIPTION FS51-SHD-200X FRONT SHROUD as shown. C-445 SCREW, 3/8”-16 X1” 2. Loosely assemble ALL the hardware C-754C FLAT WASHER, 3/8” shown in this step. C-749 LOCKWASHER, 3/8”... -
Page 23: Rear Shroud
12: I NSTALL THE HROUD QTY. ESCRIPTION 1. Place the lower rear shroud pegs into FS-SHD-250X REAR SHROUD the corresponding holes at the bottom C-444 SCREW, 3/8”-16 X 3/4” of the upright frame. C-754C FLAT WASHER, 3/8” 2. Align the holes in the top shroud C-766A LOCK NUT, 3/8”... -
Page 24: Top Cap
13: I NSTALL THE QTY. ESCRIPTION 1. Assemble the top cap brackets as shown. FS-CAP-000X TOP CAP 1. Lower the top cap on to the top of the C 675D SCREW, 1/4”-20 X 1/2”, BHCS upright. FS-BKT-001 TOP CAP BRACKET 2. -
Page 25: Bolt Caps
14: I NSTALL THE 1. Assemble the plastic bolt caps to cover ESCRIPTION each exposed bolt on the machine. The C-955 BOLT CAP caps will snap on to the bolt cap base installed with the hardware. X 37... -
Page 26: Tack Abel
15: W EIGHT TACK ABEL 1. Select the appropriate weight stack label(s) according to your order. You can install pound labels, kilogram labels, or both. 2. If you ordered a 170 lb. weight stack, use labels: LBL-WSE-01170 (for pounds) LBL-WSM-01170 (for kilograms). 3. -
Page 27: Machine Labels
ACHINE ABELS The following are the Warning labels required for this FS machine. If any of these labels are missing or become damaged, TRUE will replace them free of charge. Note: these labels are not to scale. WARNING WARNING WARNING... -
Page 28: Service
B T A I N E R V I C E For warranty service, contact an Authorized TRUE Dealer or a TRUE Customer Service representative at 1-800-883-8783 or by e-mail at service@truefitness.com. Before you call, please have the following information ready. -
Page 29: Floor
(European) safety standards for stability (without floor anchors) when the machine is used for it’s intended purpose as designated by the manufacturer. However, TRUE strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability. -
Page 30: Bolting The Machine To The Warranty
Hours of operation 8:30am - 5:00 pm CST workmanship for a 10 years. The frame is warranted for labor and freight (for parts shipped from TRUE) for one year from date of purchase. * This limited warranty on structural frame does not include paint or coatings. - Page 31 (if anyone other than a TRUE authorized dealer/ technician initially assembles and installs the Product, this The FS-51 comes with one serial number on the base of the Limited Warranty will be void unless the written authorization machine. Please write down your serial number below and keep of TRUE is first obtained).
- Page 32 If you prefer to mail your warranty card, have the owner of the product complete the information below and return it to TRUE Fitness within 30 days from the date of equipment installation.
Need help?
Do you have a question about the FS-51 and is the answer not in the manual?
Questions and answers