Advertisement
D o Not touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot.
8
D o Not use this product to perform a task for which it has not been designed.
8
D o Not deface the certification plate attached to the compressor tank.
8
D o Not cover the compressor or restrict air flow around the unit whilst operating.
8
▲
D ANGer! Do Not direct the output jet of air towards people or animals.
Do Not operate the compressor without an air filter.
8
Do Not allow anyone to operate the compressor unless they have received full instructions.
8
W ArNiNG! The air tank is a pressure vessel and the following safety measures apply:
‰
Do Not tamper with the safety valve, Do Not modify or alter the tank in any way and Do Not strap anything to the tank.
8
Do Not subject the tank to impact, vibration or to heat and Do Not allow contact with abrasives or corrosives.
8
W ArNiNG! If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
When not in use, store the compressor carefully in a safe, dry, childproof location.
9
2. iNtroDuCtioN
Aluminium cylinder head with cast iron cylinder gives added resistance to wear. Suitable for general purpose workshop applications. Pump
head directly coupled to heavy-duty induction motor for reliable and quiet operation. Welded tank complies with latest European standards.
Fitted with fully automatic pressure cut-out switch with twin gauges displaying tank and working pressures. Fitted with non-rewirable plug.
3. speCifiCAtioN
model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . sAC2420A
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . .6.8(193)cfm
Maximum Free Air Delivery cfm(ltr/min): . . . . . . . .4.6(130)
maximum Pressure: . . . . . . . . . . . . . . . . . . . . . 116psi(8bar)
minimum Rated Supply: . . . . . . . . . . . . . . . . . . . . . . . . . 13A
motor output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2hp
outlet: . . . . . . . . . . . . . . . . . . . . . . . Quick Release Coupling
Phase: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1ph
Fuse Rating: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Amp
Receiver Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24ltr
Size (W x D x H): . . . . . . . . . . . . . . . . . 600 x 290 x 585mm
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
noise level: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97dB(A)
4. AssemBlY
4.1.
Remove compressor from packaging and inspect for any shortages
or damage. If anything is found to be missing or damaged, contact
your supplier.
4.2.
Confirm that the mains voltage corresponds with the voltage shown on the compressor data plate.
4.3.
The compressor should be installed on a flat surface, or one that does not exceed 10° either transversely or longitudinally, (see fig.2)
and should be in a position that allows good air circulation around the unit.
4.4.
The compressor is supplied without oil in it. The oil is in a separate container. Remove the transit plug from the oil filler aperture, pour oil
into the aperture until it has reached the correct level on the sight (fig.3). Fit the oil filler/breather supplied into the aperture.
4.5.
Ensure that the air vent in the oil filler/breather is free from debris. If the air vent is blocked, pressure can build up in the crankcase
causing damage to the compressor and possible personal injury.
4.6.
If it is not already fitted, screw the air filter holder into the inlet port (fig.4).
importANt Take care when selecting tools for use with the compressor. Air tool manufacturers normally express the volume of air
required to operate a tool in cubic feet per minute (cfm). This refers to free air delivered by the compressor ('air out') which varies
according to the pressure setting. Do Not confuse this with the compressor displacement which is the air taken in by the compressor
('air in'). 'Air out' is always less than 'air in' - due to losses within the compressor - and so it is important that, before choosing
equipment, you study the 'Free Air Delivery' figures shown in the Specification Chart.
fig.2
5. operAtioN
WArNiNG! eNsure thAt You hAve reAD, uNDerstooD AND ApplieD seCtioN 1 sAfetY iNstruCtioNs.
‰
5.1.
Make sure that the main switch (fig.5.1) is 'OFF' (down).
5.2.
Check the oil level by looking through the sight glass (fig.3).
5.3.
ensure that the tank drain valve is closed (fig.1).
5.4.
Connect the air tool required to the compressor via an air line connected to the air outlet.
5.5.
Plug the mains plug into the mains supply and start the compressor by pulling up the main switch (fig.5.1).
5.6.
Allow the pressure in the tank to rise to the maximum at which point the compressor will automatically cut out. Tank pressure is shown
on the larger gauge (fig.5.6).
5.7.
Begin to gradually open the regulator by turning the knob clockwise (fig.5.2) until the small gauge registers the required operating
pressure specified for the tool to be used. Always adjust up to the required pressure rather than down from a higher pressure. The
required setting, once achieved, can be locked by screwing the locking ring (fig.5.3) up tight underneath the adjusting knob.
© Jack Sealey limited
Original Language Version
fig.1
fig.3
SAC2420A, SAC2420APK | Issue 1 12/06/19
fig.4
Advertisement
