Advertisement
1.2.
GENERAL SAFETY
Familiarise yourself with the application and limitations of the compressor.
9
Ensure the compressor is in good order and condition before use. If in any doubt DO NOT use the unit and contact your Sealey Stockist.
9
WARNING! Item must be serviced by an authorised agent. DO NOT tamper with or attempt to adjust pressure switch or safety valve.
‰
DO NOT carry out any welding operations on any pressurised part of the vessel.
8
Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tank pressure has
9
been vented.
9
Maintain the compressor in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate your warranty.
Read the instructions relating to any accessory to be used with this compressor. Ensure the safe working pressure of any air appliance
9
used exceeds compressors output pressure. If using a spray gun, check that the area selected for spraying is provided with an air change
system/ventilation.
Ensure the air supply valve is turned off before disconnecting the air supply hose to move a transportable compressor use the
9
handle only. Lift the compressor so that the front leg gives enough clearance for manoeuvring but maintain unit's centre of gravity in front
9
of the wheels. DO NOT attempt to lift or move the compressor by any other means.
Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
9
Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
9
Ensure the air hose is not tangled, twisted or pinched.
9
Keep children and unauthorised persons away from the working area.
9
Only move the compressor by the handle (if portable).
9
DO NOT dis-assemble compressor for any reason. The unit must be checked by qualified personnel only.
8
DO NOT use the compressor outdoors, or in damp, or wet, locations.
8
DO NOT operate within the vicinity of flammable liquids, gases or solids.
8
DO NOT touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot.
8
DO NOT use this product to perform a task for which it has not been designed.
8
DO NOT deface the certification plate attached to the compressor tank.
8
DO NOT cover the compressor or restrict air flow around the unit whilst operating.
8
▲
DANGER! DO NOT direct the output jet of air towards people or animals.
DO NOT operate the compressor without an air filter.
8
DO NOT allow anyone to operate the compressor unless they have received full instructions.
8
WARNING! The air tank is a pressure vessel and the following safety measures apply:
‰
DO NOT tamper with the safety valve, DO NOT modify or alter the tank in any way and DO NOT strap anything to the tank.
8
DO NOT subject the tank to impact, vibration or to heat and DO NOT allow contact with abrasives or corrosives.
8
Drain condensation from tank daily and inspect inside walls for corrosion every three months and have a detailed tank inspection carried
9
out annually. The tank shell must not fall below the certified thickness at any point.
WARNING! If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
When not in use, store the compressor carefully in a safe, dry, childproof location.
9
When the compressor is not in use, it should be switched off, disconnected from the mains supply and the air drained from the tank.
9
Under the PRESSURE SYSTEMS SAFETY REGULATIONS 2000 it is the responsibility of the owner of the compressor to initiate a
9
system of inspection that both defines the frequency of the inspection and appoints a person who has specific responsibility for carrying
out the inspection.
2.
INTRODUCTION
i
Belt driven pump with aluminium cylinders and cast iron liners for reduced weight and improved resistance to wear. Fitted with a 3hp motor.
Heavy-duty drive guards protect belt and flywheel that is designed to force air over the pump to aid cooling. Suitable for general purpose workshop
applications. Precision welded receiver tank manufactured to meet Pressure Vessel Directive.
3.
SPECIFICATION
i
Model:
Motor Output (HP):
Voltage / Phase:
Input current:
Speed (rpm):
Air Displacement (cfm/Lm):
Outlet:
Max Free Air Delivery (cfm/Lm):
Max Pressure (psi/bar):
Tank Capacity (L):
Dimensions (WxDxH) (mm):
Noise (dB(A)):
4. ASSEMBLY
4.1.
Remove compressor from packaging and inspect for shortages/damage. If items are missing or damaged contact your supplier.
4.2.
Save the packing material for future transportation of the compressor. We recommend that you store the packing in a safe location, at
least for the period of the guarantee. Then, if necessary, it will be easier to send the compressor to the service centre.
4.3.
Assemble the fixed wheels / castor wheel / rubber feet to the compressor as required (see fig.1).
© Jack Sealey Limited
SAC20030B
3
230/1
13A
1000
10.8/305
Quick release coupling
5.3/150
116/8
200L
1650 x 520 x 820
97
Original Language Version
SAC15030B
3
230/1
13A
1000
10.8/305
Quick release coupling
5.3/150
116/8
150L
1300 x 510 x 815
97
SAC20030B, SAC15030B Issue: 1 08/03/21
Advertisement
