Advertisement
Safety Instructions
1. Read these safety instructions carefully.
2. Retain this startup manual for future reference.
3. Disconnect the equipment from all AC outlets before
cleaning. Use only a damp cloth for cleaning. Do not
use liquid or spray detergents.
4. For pluggable equipment, the power outlet socket must
be located near the equipment and easily accessible.
5. Protect the equipment from humidity.
6. Place the equipment on a reliable surface during instal-
lation. Dropping or letting it fall may cause damage.
7. Ensure that the voltage of the power source is correct
before connecting the equipment to a power outlet.
8. Position the power cord away from high-traffic areas.
Do not place anything over the power cord.
9. All cautions and warnings on the equipment should be
noted.
10. If the equipment is not used for a long time, discon-
nect it from the power source to avoid damage from
transient overvoltage.
11. Never pour liquid into an opening. This may cause fire
or electrical shock.
12. Never open the equipment. For safety reasons, the
equipment should be opened only by qualified service
personnel.
13. If one of the following occurs, have the equipment
checked by service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the equipment.
- The equipment has been exposed to moisture.
- The equipment is malfunctioning or does not operate
according to the startup manual.
- The equipment has been dropped and damaged.
- The equipment shows obvious signs of breakage.
14. Do not leave this equipment in an environment with a
storage temperature of below -40 °C (-40 °F) or above
85 °C (185 °F) as this may cause damage. The equip-
ment should be kept in a controlled environment.
15. Caution: The battery is at risk of exploding if incorrectly
replaced. Replace only with the same or equivalent
type as recommended by the manufacturer. Discard
used batteries according to the manufacturer's instruc-
tions.
ATTENTION: DANGER D'EXPLOSION SI LA
BATTERIE EST INEXACTEMENT REMPLACÉE.
REMPLACEZ SEULEMENT AVEC LA MÊME CHOSE
OU LE TYPE ÉQUIVALENT RECOMMANDÉ PAR LE
FABRICANT. JETTENT LES BATTERIES UTILISÉES
INSTRUCTIONS DE S SELON FABRICANT DES'
16. This equipment has been tested and found to comply
with the limits for a Class A digital device. Operation of
this equipment in a residential area is likely to cause
harmful interference to radio communications, in such
cases users are required to correct the interference.
17. This equipment is sold without a power cord. We rec-
ommended users purchase a CCC-certified power cord.
In accordance with the IEC 704-1:1982 specifications, the
sound pressure level at the operator's position does not
exceed 70 dB (A).
DISCLAIMER: These instructions are provided in accor-
dance with the IEC 704-1 standard. Advantech disclaims all
responsibility for the accuracy of any statements contained
herein.
4 ITA-5231 Startup Manual
Safety Precautions - Static Electricity
Follow these simple precautions to protect yourself from
harm and the products from damage.
1. To avoid electric shock, always disconnect the power
from the PC chassis before manual handling.
2. Disconnect all power before making any configuration
changes. A sudden rush of power after connecting
a jumper or installing a card may damage sensitive
electronic components.
3. Only experienced electronics personnel should open
the chassis.
4. Always ground yourself to remove any static electrical
charge before touching the motherboard, backplane,
or add-on cards. Modern electronic devices are very
sensitive to static electric charges. Use a grounding
wrist strap at all times.
5. Place all electronic components on a static-dissipative
surface or in a static shielded bag.
6. This product is intended to be supplied by a listed DC
power source, rated 24V/48V/72V/110V, and TMA 50
°C. If you require further assistance, contact Advantech
for additional information.
7. CAUTION: Only one module can be extracted at any
one time. Additionally, ITAM-I/O modules do not support
hot swapping. Turn off the equipment power before
extraction. Moreover, do not leave the slot empty
after extracting the board. The alternative board or a
dummy module must be inserted immediately for safety
reasons.
Installation Notes
When the equipment is powered on, do not place any cov-
ering within 30 mm of the heatsink to avoid any restriction
to airflow.
When the equipment is installed on a rackmount, ensure
that the fin direction is parallel to the direction of airflow.
This greatly increases the cooling efficiency.
Advertisement
