Automate AM6 Owner's Manual page 28

Remote start keyless entry system
Table of Contents

Advertisement

T T o o a a r r m m u u s s i i n n g g y y o o u u r r r r e e m m o o t t e e
■ To arm the system press
nected). The LED will begin to flash. The Failsafe
vent the vehicle's starter from cranking if it has been installed. The ve-
hicle's horn (if connected) will honk and the parking lights will flash
once to confirm arming of the system.
T T o o d d i i s s a a r r m m u u s s i i n n g g y y o o u u r r r r e e m m o o t t e e
■ To disarm the system press
connected). The Failsafe
cle's horn (if connected) will honk twice and the parking lights will flash
twice.
D D i i s s a a b b l l i i n n g g t t h h e e F F a a i i l l s s a a f f e e
■ Turn on the ignition. Press and release the Valet button within 10 sec-
onds. The LED will stop flashing and the vehicle should start. Be sure to
check with the installer for the location of the Valet button.
T T o o r r e e m m o o t t e e s s t t a a r r t t t t h h e e v v e e h h i i c c l l e e
■ Press
nected) and the vehicle will start and run for the programmed amount
of time.
T T o o e e n n t t e e r r o o r r e e x x i i t t V V a a l l e e t t M M o o d d e e
■ Turn the ignition to the "ON" position. Turn the ignition back off. Press
and release the Valet button within 10 seconds. The status LED will light
steadily if you have entered Valet Mode. To exit Valet Mode, repeat the
steps above. The LED will turn off when exiting Valet Mode.
T T o o a a c c t t i i v v a a t t e e P P a a n n i i c c M M o o d d e e
■ Press and hold
T T o o d d i i s s a a b b l l e e t t h h e e r r e e m m o o t t e e s s t t a a r r t t s s y y s s t t e e m m
■ To disable the remote start, move the shutdown toggle switch to the OFF
position.
L L o o c c a a t t i i o o n n o o f f S S h h u u t t d d o o w w n n S S w w i i t t c c h h _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2005 Directed Electronics—all rights reserved
©
Q Q u u i i c c k k R R e e f f e e r r e e n n c c e e G G u u i i d d e e
for one second. The doors will lock (if con-
®
Starter Kill will be deactivated and the vehi-
®
S S t t a a r r t t e e r r K K i i l l l l w w i i t t h h o o u u t t a a t t r r a a n n s s m m i i t t t t e e r r
twice within 3 seconds. The parking lights will turn on (if con-
for 1.5 seconds.
®
Starter Kill will pre-
for one second. The doors will unlock (if
2 2 5 5

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Automate AM6 and is the answer not in the manual?

Questions and answers

Dale
March 25, 2025

Door lock and unlock doesn’t work

1 comments:
Mr. Anderson
March 25, 2025

The door lock and unlock may not be working on the Automate AM6 for several reasons:

1. Not Connected – The system requires proper connection to the vehicle's power door locks. If the wiring is incorrect or disconnected, the locks will not function.
2. Extra Parts Required – Some door lock systems need additional parts for compatibility. Check if your vehicle requires extra components.
3. Programming Issue – The system can be programmed to lock and unlock automatically. If it is not set up correctly, the feature may not work.
4. Failsafe® Starter Kill Activation – If this feature is engaged, it may prevent the system from operating normally. Disarm the system to check.
5. Faulty Module or Switch – If the factory door switch or module has failed, the automate system may have been installed as a workaround. If this module is also faulty, door locks may not work.

Check wiring, programming, and system components to diagnose the issue.

This answer is automatically generated

Table of Contents

Save PDF