Do you have a question about the Automate AM6 and is the answer not in the manual?
Questions and answers
Dale
March 25, 2025
Door lock and unlock doesn’t work
1 comments:
Mr. Anderson
March 25, 2025
The door lock and unlock may not be working on the Automate AM6 for several reasons:
1. Not Connected – The system requires proper connection to the vehicle's power door locks. If the wiring is incorrect or disconnected, the locks will not function. 2. Extra Parts Required – Some door lock systems need additional parts for compatibility. Check if your vehicle requires extra components. 3. Programming Issue – The system can be programmed to lock and unlock automatically. If it is not set up correctly, the feature may not work. 4. Failsafe® Starter Kill Activation – If this feature is engaged, it may prevent the system from operating normally. Disarm the system to check. 5. Faulty Module or Switch – If the factory door switch or module has failed, the automate system may have been installed as a workaround. If this module is also faulty, door locks may not work.
Check wiring, programming, and system components to diagnose the issue.
Page 1
M M o o d d e e l l A A M M 6 6 O O w w n n e e r r ' ' s s G G u u i i d d e e...
Page 2
L L i i m m i i t t e e d d L L i i f f e e t t i i m m e e C C o o n n s s u u m m e e r r W W a a r r r r a a n n t t y y Directed Electronics promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed Electronics unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated...
Page 3
W W H H A A T T S S O O E E V V E E R R , , I I N N C C L L U U D D I I N N G G W W I I T T H H O O U U T T L L I I M M I I T T A A T T I I O O N N , , L L I I A A B B I I L L I I T T Y Y F F O O R R T T H H E E F F T T , , D D A A M M A A G G E E A A N N D D / / O O R R V V A A N N D D A A L L I I S S M M .
T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s L L i i m m i i t t e e d d L L i i f f e e t t i i m m e e C C o o n n s s u u m m e e r r W W a a r r r r a a n n t t y y ............i i S S t t a a n n d d a a r r d d C C o o n n f f i i g g u u r r a a t t i i o o n n .
Page 5
S S t t a a n n d d a a r r d d C C o o n n f f i i g g u u r r a a t t i i o o n n controls the A A r r m m / / P P a a n n i i c c O O N N / / P P a a n n i i c c O O F F F F function.
Page 6
W W h h a a t t i i s s I I n n c c l l u u d d e e d d ■ The control module ■ An HX receiver/antenna ■ Two four-button transmitters ■...
S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e The system requires no specific maintenance. Your remote is powered by a small, lightweight 3-volt lithium battery that will last approx- imately one year under normal use.
T T r r a a n n s s m m i i t t t t e e r r F F u u n n c c t t i i o o n n s s The receiver uses a computer-based learn routine to learn the transmitter buttons.
Page 9
B B u u t t t t o o n n The remote start function of your system is controlled by pressing this button twice within 3 seconds. Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these but- tons simultaneously.
Page 10
partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle.
■ After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the prod- uct installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed.
The system can also be programmed to arm the optional Failsafe Starter Kill automatically (called Passive Mode). If the system has been programmed for Passive Mode, the Failsafe automatically activate 30 seconds after the ignition has been turned off. After the ignition has been turned off, the status LED will flash rapidly to indicate that the system is in Passive Mode.
D D i i s s a a b b l l i i n n g g t t h h e e S S t t a a r r t t e e r r K K i i l l l l W W i i t t h h o o u u t t a a T T r r a a n n s s m m i i t t t t e e r r If your remote transmitter is lost or damaged, you can manually override the starter kill.
R R e e m m o o t t e e S S t t a a r r t t This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehi- cle with the climate control system.
To turn the rear defogger output ON: Simultaneously press & release the on the remote control. The lights will flash 3 times. The rear defogger output will once again activate when the vehicle is remote started. N N O O T T E E : : If the remote start is on the lights will turn off then flash 3-times before returning to their normal output and the defogger output will activate as programmed.
S S h h o o r r t t - - R R u u n n / / T T u u r r b b o o Short-run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1, 3 ,5 or 10 min- utes.
Page 19
Press Timer mode buttons. The vehicle will confirm with 4 parking light flashes. A 1-second delay will start. The system will start the car and will run for the specified duration, unless shut down by the remote start button . If shut down with the remote start button will remain in timer mode.
Page 20
S S t t a a r r t t e e r r A A n n t t i i - - G G r r i i n n d d C C i i r r c c u u i i t t r r y y Whenever the vehicle is remote started, advanced anti-grind cir- cuitry prevents the starter from engaging, even if the key is turned to the start position.
Page 21
R R a a p p i i d d R R e e s s u u m m e e L L o o g g i i c c This Directed Electronics system will store its current state to non- volatile memory.
Page 22
■ Comfort closure is a programming option which closes the vehicle’s windows after remote locking. ■ Parking lights f f l l a a s s h h i i n n g g or constant. Your system can be pro- grammed to either flash or to turn on the parking lights con- stantly during the entire remote start operation.
Page 23
G G l l o o s s s s a a r r y y o o f f T T e e r r m m s s C C o o n n t t r r o o l l U U n n i i t t : The “brain” of your system. Usually hidden under- neath the dash area of the vehicle.
Page 24
C C o o n n v v e e n n i i e e n n c c e e E E x x p p a a n n s s i i o o n n s s Listed below are some of the many expansion options available for use with your system.
Page 25
P P o o w w e e r r W W i i n n d d o o w w C C o o n n t t r r o o l l : : Power window control is provided with Directed Electronics 529T or 530T systems.
Page 28
Q Q u u i i c c k k R R e e f f e e r r e e n n c c e e G G u u i i d d e e T T o o a a r r m m u u s s i i n n g g y y o o u u r r r r e e m m o o t t e e ■...
Page 29
V V a a l l e e t t T T a a k k e e o o v v e e r r ■ Press and release ignition key to the OFF position. Once the vehicle has started, it will run for the pre-programmed period of time (12, 24, or 60 minutes).
Page 30
T T h h e e c c o o m m p p a a n n y y b b e e h h i i n n d d t t h h i i s s s s y y s s t t e e m m i i s s D D i i r r e e c c t t e e d d E E l l e e c c t t r r o o n n i i c c s s Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available.
Need help?
Do you have a question about the Automate AM6 and is the answer not in the manual?
Questions and answers
Door lock and unlock doesn’t work
The door lock and unlock may not be working on the Automate AM6 for several reasons:
1. Not Connected – The system requires proper connection to the vehicle's power door locks. If the wiring is incorrect or disconnected, the locks will not function.
2. Extra Parts Required – Some door lock systems need additional parts for compatibility. Check if your vehicle requires extra components.
3. Programming Issue – The system can be programmed to lock and unlock automatically. If it is not set up correctly, the feature may not work.
4. Failsafe® Starter Kill Activation – If this feature is engaged, it may prevent the system from operating normally. Disarm the system to check.
5. Faulty Module or Switch – If the factory door switch or module has failed, the automate system may have been installed as a workaround. If this module is also faulty, door locks may not work.
Check wiring, programming, and system components to diagnose the issue.
This answer is automatically generated