Table of Contents
Advertisement
■
After the remote start module has been installed, contact your
authorized dealer to have him or her test the remote start
module by performing the Safety Check outlined in the prod-
uct installation guide. If the vehicle starts when performing
the Neutral Safety Shutdown Circuit test, the remote start unit
has not been properly installed. The remote start module must
be removed or the installer must properly reinstall the remote
start system so that the vehicle does not start in gear. All
installations must be performed by an authorized Directed
Electronics dealer. O O P P E E R R A A T T I I O O N N O O F F T T H H E E R R E E M M O O T T E E S S T T A A R R T T M M O O D D U U L L E E
I I F F T T H H E E V V E E H H I I C C L L E E S S T T A A R R T T S S I I N N G G E E A A R R I I S S C C O O N N T T R R A A R R Y Y T T O O I I T T S S I I N N T T E E N N D D - -
E E D D M M O O D D E E O O F F O O P P E E R R A A T T I I O O N N . . O O P P E E R R A A T T I I N N G G T T H H E E R R E E M M O O T T E E S S T T A A R R T T S S Y Y S S - -
T T E E M M U U N N D D E E R R T T H H E E S S E E C C O O N N D D I I T T I I O O N N S S M M A A Y Y R R E E S S U U L L T T I I N N P P R R O O P P E E R R T T Y Y
D D A A M M A A G G E E O O R R P P E E R R S S O O N N A A L L I I N N J J U U R R Y Y . . Y Y O O U U M M U U S S T T I I M M M M E E D D I I A A T T E E L L Y Y
C C E E A A S S E E T T H H E E U U S S E E O O F F T T H H E E U U N N I I T T A A N N D D S S E E E E K K T T H H E E A A S S S S I I S S T T A A N N C C E E O O F F A A N N
A A U U T T H H O O R R I I Z Z E E D D D D I I R R E E C C T T E E D D E E L L E E C C T T R R O O N N I I C C S S D D E E A A L L E E R R T T O O R R E E P P A A I I R R O O R R
D D I I S S C C O O N N N N E E C C T T T T H H E E I I N N S S T T A A L L L L E E D D R R E E M M O O T T E E S S T T A A R R T T M M O O D D U U L L E E . . D D I I R R E E C C T T - -
E E D D E E L L E E C C T T R R O O N N I I C C S S W W I I L L L L N N O O T T B B E E H H E E L L D D R R E E S S P P O O N N S S I I B B L L E E O O R R P P A A Y Y F F O O R R
I I N N S S T T A A L L L L A A T T I I O O N N O O R R R R E E I I N N S S T T A A L L L L A A T T I I O O N N C C O O S S T T S S . .
A A r r m m i i n n g g
Pressing
for one second arms the system by activating the
starter kill and locking the doors (if the door locks are connected).
The horn will honk (if connected) and the parking lights will flash
once to confirm arming of the system. While the system is armed,
the status LED will flash once per second. The Failsafe
(if installed) will also prevent the vehicle's starter from cranking.
8 8
2005 Directed Electronics—all rights reserved
©
®
Starter Kill
- Quick Links:
- Table of Contents
- Standard Configuration
- Arming
- Valet Mode
- Remote Start
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Automate AM6 and is the answer not in the manual?
Questions and answers
Door lock and unlock doesn’t work
The door lock and unlock may not be working on the Automate AM6 for several reasons:
1. Not Connected – The system requires proper connection to the vehicle's power door locks. If the wiring is incorrect or disconnected, the locks will not function.
2. Extra Parts Required – Some door lock systems need additional parts for compatibility. Check if your vehicle requires extra components.
3. Programming Issue – The system can be programmed to lock and unlock automatically. If it is not set up correctly, the feature may not work.
4. Failsafe® Starter Kill Activation – If this feature is engaged, it may prevent the system from operating normally. Disarm the system to check.
5. Faulty Module or Switch – If the factory door switch or module has failed, the automate system may have been installed as a workaround. If this module is also faulty, door locks may not work.
Check wiring, programming, and system components to diagnose the issue.
This answer is automatically generated