Table of Contents
Advertisement
Quick Links
Super First Metal Swing Set
ASSEMBLY, INSTALLATION, CARE, MAINTENANCE AND USER INSTRUCTIONS
This product is designed to be used simultaneously by up to 6 children between ages 3 to 8.
Maximum weight of each user is 100lbs (45kg). Combined weight of all users must not exceed
600lbs (270kg).
Carefully read this entire instruction manual before you start to assemble or use this swing set.
You must follow all instructions and warnings while using this equipment.
Do not use this swing set on hard packed soil, concrete or any kind of hard surface.
This equipment must be anchored (anchors not included). You should consult your local
contractor regarding the best way to anchor the product in your location of installation.
Assembly requires at least two adults.
For Customer Service, please call 1-866-370-2131 or visit
Flat M, Kaiser Estate Phase 3, 11 Hok Yuen Street, Hunghom, Kowloon, Hong Kong
MODEL#MSC-4146
OWNER'S MANUAL
FOR RESIDENTIAL USE ONLY
Save this instruction manual for future reference
Monday – Friday 9:00 AM – 5:00 PM Eastern Time
Sportspower Ltd.
Corporate Office 1-800-497-6106
WARNING
1
www.sportspowerltd.net
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SPORTSPOWER MSC-4146
Summary of Contents for SPORTSPOWER MSC-4146
- Page 1 Super First Metal Swing Set MODEL#MSC-4146 OWNER’S MANUAL ASSEMBLY, INSTALLATION, CARE, MAINTENANCE AND USER INSTRUCTIONS FOR RESIDENTIAL USE ONLY WARNING This product is designed to be used simultaneously by up to 6 children between ages 3 to 8. ...
- Page 2 INTRODUCTION Dear Valued Customer, Congratulations on your Sportspower play set purchase! Please read and completely understand the contents of this owner’s manual. This manual contains specific instructions and warnings that must be followed to prevent injuries. This play set is for residential use only. This play set is NOT intended for public or commercial use. The warranty will be voided if the play set is used in a commercial application.
-
Page 3: Table Of Contents
TABLE OF CONTENTS IMPORTANT INSTRUCTIONS AND WARNINGS........................ 4 IMPORTANT CONSUMER INFORMATION SHEET ......................8 ANCHORING ................................... 9 CARE AND MAINTENANCE CHECKLIST ......................... 11 TOOLS NEEDED ................................... 12 PARTS LIST ................................... 13 ASSEMBLY AND INSTALLATION INSTRUCTIONS ......................17 AREA OF INSTALLATION - SWING SET TOP BAR...................... 17 AREA OF INSTALLATION - SIDE LEGS ........................ -
Page 4: Important Instructions And Warnings
IMPORTANT INSTRUCTIONS AND WARNINGS WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT AGE LIMIT This product is designed to be used by up to eight (6) children between the ages of 3 to 8. Maximum user weight is 100 pounds (45kg) each with a combined maximum weight of 600 pounds (270kg). ... - Page 5 Some consumers want an anchoring system that allows the product to be moved to different locations. Other consumers want to keep their swing set in a permanent location. There are different types and different methods of anchoring this product. Sportspower does not make a specific anchoring recommendation as each consumer’s needs and conditions can vary.
- Page 6 PLAY SUPERVISION DO NOT allow more than one child to play on the individual swing, trapeze or slide component at any one time. DO NOT allow children to stand on the slide, swing seats or glide ride. DO NOT allow children to walk too close to moving parts.
- Page 7 INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. ...
-
Page 8: Important Consumer Information Sheet
IMPORTANT CONSUMER INFORMATION SHEET The Consumer Product Safety Commission estimates there are more than 200,000 playground related injuries involving children each year. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. -
Page 9: Anchoring
ANCHORING (NOTE:ANCHORS ARE NOT INCLUDED - MUST BE PURCHASED SEPARATELY) There are different ways of anchoring the equipment, depending on the type of ground on which the equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping. You should consult your local contractor to decide the most appropriate way to anchor the equipment in your location. - Page 10 FRAME 12-5/8” CONCRETE 5” 2” BRICK OR GRAVEL Note: The maximum fall height for this product is 6 feet. The minimum ground clearance between the bottom of the suspended plays and the playing or ground surface must be 8 inches. You must maintain a minimum of 8 inches of ground clearance.
-
Page 11: Care And Maintenance Checklist
CARE AND MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: Tighten all hardware. Lubricate all metallic moving parts per manufacturer’s instructions. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing. ... -
Page 13: Parts List
PARTS LIST Part list for main frame assembly Part No. Picture Description Quantity LEFT TOP BARS RIGHT TOP BAR TOP SECTION LEG BOTTOM SECTION LEG(WITH FOAM) BOTTOM SECTION LEG A4-1 (WITH EXTRA HOLES FOR TEETER-TOTTER) CROSS BAR CROSS BAR (FOR SLIDE) END CAP (PRE-ASSEMBLED) BOLT 5/16”... - Page 14 Part No. Picture Description Quantity TRAPEZE EYEBOLT WITH ATTACHMENT BOLT(PRE-ASSEMBLED) RUBBER CAP (PRE-ASSEMBLED) NYLON NUT 5/16” ARC PLASTIC CAP Part list for slide assembly X1-N SLIDE SUPPORT (WITH OPENING) X2-N SLIDE SUPPORT X3-N SLIDE LEG TUBE X4-N SLIDE TOP SUPPORT BAR X5-N SLIDE FRONT SUPPORT SLIDE LADDER STEPS...
- Page 15 Part No. Picture Description Quantity SEAT SEAT SUPPORT HANDLE BAR LEFT HANDLE BAR SUPPORT U19-1 RIGHT HANDLE BAR SUPPORT U19-2 L SHAPED TUBE BOLT 5/16" x 3-2/9" (8mm x 82mm) BOLT 5/16" x 2-8/11" (8mm x 63mm) BOLT 5/18" x 2-9/13" (8mm x 68mm) ARC WASHER Φ8.5Φ19*T1.5mm NYLON NUT 5/16”...
- Page 16 Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface;...
-
Page 17: Assembly And Installation Instructions
ASSEMBLY AND INSTALLATION INSTRUCTIONS AREA OF INSTALLATION - SWING SET TOP BAR Step 1 - Assemble the top bar frame of the swing set Connect A1 and A2. Secure with B1, B5, B4 and B3 as shown below in FIGURE 1. NOTE: Please make sure that concave holes face down and round holes face up. -
Page 18: Area Of Installation - Side Legs
AREA OF INSTALLATION – TOP SECTION LEGS Step 2 - Assemble top section legs of swing set Connect A3 to A1 and secure using B1, B5, B4 and B3 as shown below in FIGURE 2. Repeat the above step for the right side of the swing set (using A2, A3). Note: Please make sure that concave holes face down and round holes face up. - Page 19 AREA OF INSTALLATION - BOTTOM SECTION LEGS Step 3 - Assemble the bottom section legs of swing set Connect A4 to A3 and secure using B1, B5, B4 and B3 as shown in FIGURE 3. On the right side of the swing set, note that A4-1 needs to be installed at the front of the swing set. NOTE: The two extra holes on A4-1 are used for connecting the teeter-totter in later steps and need to be placed towards the front of the swing set.
-
Page 20: Area Of Installation - Cross Bars
AREA OF INSTALLATION - CROSS BARS Step 4 - Attach the crossbar to the support legs Attach A6 to the outer side of A4 and secure using B1, B6, B4 and B3. Attach A5 to the outer side of A4 and A4-1 (right side of teeter totter) using B1, B6, B4 and B3. IMPORTANT: Please note that A6 has two extra holes that will be used for connection to the slide in later steps. -
Page 21: Area Of Installation - Swing Seat
AREA OF INSTALLATION - SWING SEAT Step 5 - Swing Seat assembly Insert Eye Bolt for Swing Chain (J3) into the holes on A1 and A2. Secure with J6 and J8 as shown in DIAGRAM A. Attach Swing Seat (K1) to J3 using J7, J9 and J6 as shown in DIAGRAM B. Note: Use the special socket wrench provided to fully tighten the bolts and nuts. -
Page 22: Area Of Installation - Trapeze
AREA OF INSTALLATION - TRAPEZE Step 6 - Trapeze Assembly Insert P2 (which is pre-assembled with P1 and P3) through the hole on A1. Secure using P5 and P4 as shown in the FIGURE 6. Note: Use the special socket wrench provided to fully tighten the bolts and nuts. FIGURE 6... -
Page 23: Area Of Installation - Slide
AREA OF INSTALLATION - SLIDE STEP 7 - Slide assembly Insert Slide Front Support (X5-N) into Slide (Y2) and secure with Z9 and Z6. Connect (X4-N) into Slide (Y2) as shown in FIGURE 7. Bolt holes face up FIGURE 7... - Page 24 STEP 8 - Slide assembly (continued) Connect Slide Ladder Steps (X6) to Slide Supports (X1-N and X2-N). Secure both sides using Z8, Z6 and Z4 as shown in FIGURE 8. Insert Slide Leg Tube (X3-N) into X1-N and X2-N as shown. Align the holes and hold in position.
- Page 25 STEP 9 - Slide assembly (continued) Secure X4-N to the ladder using Z1, Z3, Z6 and Z5 as shown in DIAGRAM A. Place Slide (Y2) onto the assembled step ladder and secure both sides to the leg tubes using Z2, Z6, Z6 and Z4 as shown in DIAGRAM B.
- Page 26 STEP 10 - Connect the slide to the swing set Connect the assembled slide to the swing set frame. Place Plastic Connector (Y1) between A6 and X2-N and secure together using Z7, Z6, Z3 and Z5 as shown in FIGURE 10. FIGURE 10...
-
Page 27: Area Of Installation - Teeter Totter
AREA OF INSTALLATION - TEETER TOTTER STEP 11 - Teeter Totter assembly Attach U20 to A4-1. Align the holes on U20 to the two holes on the bottom of A4-1 and secure using U3, U4, U15 and U5 as shown in the enlarged diagram of FIGURE 11. FIGURE 11... - Page 28 STEP 12 - Teeter Totter assembly (continued) Secure U17 to U20 using U2, U14, U10 and U5 as shown in the enlarged diagram of FIGURE 12. FIGURE 12...
- Page 29 STEP 13 - Teeter Totter assembly (continued) Attach U18 to U19-1 and U19-2 and secure using U9 and U21. Repeat for the other set of U18, U19-1 and U19-2. FIGURE 13...
- Page 30 STEP 14 - Teeter Totter assembly (continued) Secure U19-1 and U19-2 to U17 using U1, U4 and U5 as shown in the enlarged diagram of FIGURE 14. Repeat in the same manner for the other side. FIGURE 14...
- Page 31 STEP 15 - Teeter Totter assembly (continued) Secure U16 to U19-1 and U19-2 using U7, U8 and U6 as shown in the enlarged diagram of FIGURE 15. FIGURE 15...
- Page 32 Do not allow access by children if any parts are missing or damaged. Call our customer service for assistance if any replacement parts are needed. Only official Sportspower genuine parts should be used. Use of non-authorized parts shall void the warranty on the product.
-
Page 33: Manufacturer's Limited Warranty
MANUFACTURER’S LIMITED WARRANTY Sportspower Ltd warrants its products to be free from defects in material and workmanship under normal use and service conditions for ninety (90) days after the date of purchase. Extended warranty from 90 to 180 days will be offered to those customers registering their products at www.sportspowerltd.net...
Need help?
Do you have a question about the MSC-4146 and is the answer not in the manual?
Questions and answers