1. Manuals
  2. Brands
  3. ACTi Manuals
  4. Security Camera
  5. CAM-6600 Series
  6. Quick installation manual

ACTi CAM-6600 series Quick Installation Manual

Ip outdoor high speed dome
Hide thumbs Also See for CAM-6600 series:
Table of Contents

Advertisement

Quick Links

Download this manual
IP Outdoor High Speed Dome
CAM-6600 series
Ver. 070307
Quick Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CAM-6600 series and is the answer not in the manual?

Questions and answers

Related Manuals for ACTi CAM-6600 series

Summary of Contents for ACTi CAM-6600 series

  • Page 1 IP Outdoor High Speed Dome CAM-6600 series Ver. 070307 Quick Installation Guide...

  • Page 2: Getting Started

    Getting Started PACKAGE CONTENTS CAM-6600 series Warranty Card Software CD Power & A/V Cable LAN/WAN Cable Alarm Cable 5.4” Transparent Cover Power Adaptor (Option) Lubricant Screws...

  • Page 3: Physical Description

    1.2 PHYSICAL DESCRIPTION Outdoor High Speed Dome Bottom 1. Reset Button Step 1: Switch off IP device by disconnecting the power cable Step 2: Press and continue to hold the Reset Button. Reconnect the power cable while continuing to hold the reset button. Step 3: Keep holding the reset button depressed around 6 seconds, release the reset button.
  • Page 4 number respectively. For instance, if the speed dome ID is 123, the ID switch should be set as below: centesimal decimal single digit NOTE: No two speed domes should be given the same ID, or communication conflict may occur. NOTE: The number “0”...
  • Page 5 6. 22 Pin Connector A 50cm data cable (shown as the figure below) is shipped with IP high speed dome. Please find it in the accessory bag. The 22-pin connector definition is listed as below. Cable AC 24-1/DC GND 20AWG Alarm Pin (Not wired) AC 24-2/DC 12(+) 20AWG...

  • Page 6: Cable Wiring

    Wiring Indication PIN NAME DESCRIPTION of Power Adapter AC24V AC 24V of Power Input Brown E-GND E-Ground Pin of Power Input Green/Yellow AC24V AC 24V of Power Input Blue Power Adpater 1.3 Cable Wiring Cable Wiring and Connection Users may need to do cable wiring when connecting alarm input and output devices. The table follows will illustrate the way to wire cords into the connector housing (shown in the figures below).
  • Page 7 To unlock the terminal, press the hook, as indicated in the figure, with a proper tool and pull it out gently. Alarm Cable Wiring The alarm pins are serviceable for connecting alarm input and output devices, such as alarm sensors, sirens or flashing lights with the surveillance system. The table shown as follows lists the definition of alarm pins on the 22-pin connector.
  • Page 8 1.4 IP High Speed Dome Setups Before installing or connecting the speed dome camera, please refer to this section and complete preparation, switch setting and communication switch settings. 1.4.1: Prepartions for Dome Setups The section will illustrate the speed dome housing installation procedure of the outdoor speed dome equipped with sunshield.
  • Page 9 Note that the tiny protrusion on the dome cover must align with one of the four holes on the dome body. STEP 5 Assemble the dome cover to the dome body by pressing the cover gently downward to the dome body with two hands on the side of the cover.

  • Page 10: Basic Connections

    1.5 Basic Connections Follow the procedures below to connect the IP high speed dome to the respective apparatuses.

  • Page 11: Quick Tour

    Quick Tour This section guides you with a quick tour on IP high speed dome. 2.1 Configure the IP High Speed Dome 2.1.1 Make sure network environment Default IP of IP high speed dome is 192.168.0.100. Please make sure IP high speed dome and your PC are on the same network segment before running the installation.
  • Page 12 2.1.2 Open Internet Explorer with IP address NOTE: If your web browser is earlier than IE6, then download IE6 is recommended. NOTE: The IP high speed dome default IP address is set to 192.168.0.100 2.1.3 Login with default administrator’s account & password NOTE: Default administrator account is set to Admin, password is set to 123456, and click...
  • Page 13 2.1.4 Preview the video NOTE: In your Client PC, please make sure the setting of Network Connections Type is set to Auto Negotation, since IP high speed dome follows MII standard. Otherwise, you might not see the live image.
  • Page 14 2.15 Set the new IP address *Host Name : Enter in the domain name, Default Host Name is ACTi. *Language : Language setting for Web Configurator after Save Reboot. Default setting is English. *IP Address : The IP address of the LAN interface. The default IP address is 192.168.0.100.
  • Page 15 2.1.6 Check Default Video Setting The streaming type [Version 1.0] – without audio function The streaming type [Version 2.0] – with audio function NOTE: Please make sure the TV Input (NTSC / PAL) is meet your requirement, and click button. 2.1.7 Click Save Reboot to restore all settings and please wait about 30 seconds for system reboot.

Table of Contents