ACTi KCM-3911 Installation Manual
Indoor hemispheric mounting on the wall face forward
Hide thumbs
Also See for KCM-3911:
- Hardware manual (26 pages) ,
- Hardware user manual (15 pages) ,
- How to use (3 pages)
Related Manuals for ACTi KCM-3911
Summary of Contents for ACTi KCM-3911
- Page 1 Indoor Hemispheric Mounting on the Wall (Face Forward) Installation Guide For Models: KCM-3911, B55, B56 2014/01/10...
-
Page 2: Table Of Contents
Installation Guide Table of Contents Introduction ................ 3 Installation Procedures of KCM-3911 ....... 4 Step 1: Unpack the Camera ..............4 Step 2: Prepare Other Device Connectors (Optional) ......4 Step 3: Install the Base Plate ..............5 Step 4: Attach the Camera to the Base Plate .......... 6 Step 5: Connect the Cables .............. -
Page 3: Introduction
Bundled surface mounting accessories and connectors vary depending on model. Refer to the installation procedures of your camera model as below: Camera Model Description Required Accessories KCM-3911 The KCM-3911 comes with a bundled Bundled Mounting Plate mounting plate for installing the camera on the surface. See Installation Procedures of KCM-3911 on page 4. -
Page 4: Installation Procedures Of Kcm-3911
Installation Guide Installation Procedures of KCM-3911 Step 1: Unpack the Camera 1. Slightly twist the cover ring counter-clockwise and pull to detach it. 2. Remove the sticker label. 3. Set the camera aside for later installation. Step 2: Prepare Other Device Connectors (Optional) The camera supports external power supply with a DC12V power adapter and digital input / output devices useful for event triggers, and audio input / output devices. -
Page 5: Step 3: Install The Base Plate
1. After considering the orientation direction, drill the three (3) holes on the surface using the drill template or the base plate itself as the template. If the cables will pass through the surface, drill also the cable hole at this point. Screw hole www.acti.com... -
Page 6: Step 4: Attach The Camera To The Base Plate
2. Secure the base plate to the surface using the supplied screws. Step 4: Attach the Camera to the Base Plate 1. Align the screw holes of the camera to the base plate. 2. Secure the camera to the base plate using the supplied screws. www.acti.com... -
Page 7: Step 5: Connect The Cables
2. Attach the cover ring, take note that the arrow on the camera should be aligned with the arrow on the cover ring. NOTE: The cables must be slightly bent underneath the cover ring. 3. Twist the ring counter-clockwise to secure the ring to the camera. www.acti.com... - Page 8 GREEN jack of the bundled audio cable. Audio Input Jack Audio Device Audio Output Jack Note: Make sure that the connected audio input device has a built-in amplifier. Connecting an ordinary microphone will dwarf sounds and will result in inaudible recording. www.acti.com...
-
Page 9: Step 6: Connect To Network
Ethernet Cable (Data) PoE Injector / Power Cable Switch Ethernet Cable AC Power (Data + Power) Source Camera Step 7: Access the Camera Live View Refer to the camera Hardware Manual downloadable from the website (www.acti.com) for more information. www.acti.com... -
Page 10: Installation Procedures Of B5X Fisheye Domes
Connectors Side 2. If the cables will pass through the surface, drill also the cable hole at this point and pull the cables through the hole on the surface. 3. Remove the drill template sticker from the surface. www.acti.com... -
Page 11: Step 2: Prepare The Camera
2. If the cables will be routed along the surface, remove the cable tab from the cover ring. If the cables will pass through the surface, skip this step. 3. Install a memory card into the memory card slot of the camera, as needed. www.acti.com... -
Page 12: Step 3: Prepare Other Device Connectors (Optional)
Refer to the following sections for detailed information: How to Connect a Power Adapter (Optional) on page 16 How to Connect DI/DO Devices (Optional) on page 18 Step 4: Install the Camera Install the camera using the three (3) supplied screws. www.acti.com... -
Page 13: Step 5: Connect The Cable(S)
PC and a power source. See Power-over-Ethernet (PoE) connection example below. Network Ethernet Cable Ethernet Cable (Data) PoE Injector / Power Cable Switch Ethernet Cable AC Power (Data + Power) Source Camera www.acti.com... -
Page 14: Step 6: Complete The Installation
1. Attach the cover ring, take note that the arrow on the camera should be aligned with the arrow on the cover ring. NOTE: If the cable(s) will be routed along the surface, route the cable(s) through the cable gap of the cover ring. 2. Twist the ring counter-clockwise to secure the ring to the camera. www.acti.com... -
Page 15: Step 7: Access The Camera Live View
Installation Guide 3. Remove the thin film protecting the lens. Step 7: Access the Camera Live View Refer to the camera Hardware Manual downloadable from the website (www.acti.com) for more information. www.acti.com... -
Page 16: Appendices
1. Loosen the screws of the 12V and GND pins of the power terminal block. 2. Take note that a standard power adapter cable has two (2) different wires: Connects to GND Pin White stripe: Connects to 12V Pin www.acti.com... - Page 17 4. Tighten the screws of the 12V pin and the GND pins to secure the wire connection. 5. Set the prepared power adapter for connection later. Below is an example of a power adapter with an attached terminal block. NOTE: The power adapter is not bundled in the package. www.acti.com...
-
Page 18: How To Connect Di/Do Devices (Optional)
DO device applications are motion-triggered lights, electric fence, magnetic door locks, etc. KCM-3911 DI/DO Connector You can connect up to two DI and two DO devices to your camera. Press and hold the orange tab as you insert the wire through the pin slot, then release the orange tab to secure the wire. - Page 19 In this case, wire connection to Pins 1 to 4. Use the GND and DI1 pins to connect a DI device and use the 12V and DO1 pins to connect a DO device. See wiring scheme below: Consequently, to connect a second DI or DO device, wire the connection to Pins 5 to 8. www.acti.com...
- Page 20 The illustration below is a graphic example of connecting a relay to a high voltage DO device. 110V-220V AC External Power Source Relay (DO1 Device) Camera Illuminator NOTE: For more information on DI/DO connections, please refer to the Knowledge Base article All about Digital Input and Digital Output downloadable from the link below (http://www.acti.com/kb/detail.asp?KB_ID=KB20091230001). www.acti.com...
-
Page 21: B5X Fisheye Dome Di/Do Connector
TTL - compatible logic levels To trigger (low) Logic level 0: 0V ~ 0.4V Voltage Normal (high) Logic level 1: 3.1V ~ 30V Current 10mA ~ 100mA Connection design Transistor (Open Collector) Voltage & Current < 24V DC, < 100mA www.acti.com... - Page 22 Even though the camera provides 12V power, this may not be enough for some high voltage DO devices, such as a ceiling light or a motor that opens or closes a gate. In this case, there is a need to connect an external relay. See wiring scheme below: www.acti.com...
- Page 23 110V-220V AC External Power Source Relay (DO1 Device) Camera Illuminator NOTE: For more information on DI/DO connections, please refer to the article All about Digital Input and Digital Output (http://www.acti.com/kb/detail.asp?KB_ID=KB20091230001) in the Knowledge Base section of our website (www.acti.com). www.acti.com...
-
Page 24: Safety Information
Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself. Refer all servicing to qualified service personnel. www.acti.com... - Page 25 Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. www.acti.com...
- Page 26 Copyright © 2014, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.com...