Setting Up The Player; Using The Setup Navigator - Pioneer DV-636D Operating Instructions Manual

Setting Up the
Player

Using the Setup Navigator

The Setup Navigator has been designed to simplify the
process of getting the DVD player ready to perform.
Designed as a series of on-screen multiple-choice
questions, the Setup Navigator automatically sets the
audio, video, and language settings according to how the
questions are answered. Once this procedure is
complete, it will be possible to begin using the DVD
player to enjoy DVDs.
The procedure on this page describes the operations
necessary to function with in the Setup Navigator
screens. A detailed description of the contents of each
question that appears on the screen can be found on
the following pages.
Procedures in this section use the DV-636D. Differences
in procedures of Taiwanese model are clearly marked by
white numbered steps.
When setting up for the first time
Some DVDs start playing automatically when loaded in
the player. Because the Setup Navigator cannot be used
if a disc is playing, it is recommended to set up the
player using the Setup Navigator before loading a DVD
for the first time. If a DVD has been loaded, be sure to
press STOP 7 before proceeding.
LAST
1 1
MEMORY
SUB TITLE
AUDIO
2
SETUP MENU
DISPLAY
¶
3
2
PREV
4
¶
7
PLAY
STOP
e E
STEP/SLOW
1 2
5
4
¶
7 8
RANDOM PROGRAM SEARCH MODE
1, 1 1
D VD PLA YER
5.1CH FL OFF
VIRTUAL
DOLBY
STANDBY
DIGITAL
SUB
5.1CH
CENTER SURROUND WOOFER MODE
POWER
DOLBY DIGITAL/DTS DECODER
– OFF - ON VIRTUAL DOLBY AUDIO SUBTITLE FL
DIGITAL DIMMER
OPEN/
CONDITION CLOSE
MEMORY
ANGLE REPEAT
REPEAT
TOP MENU A-B
RETURN
5 5 ¶
4
3
NEXT
¢
∞ ¶
3 8
PAUSE
¶
1 ¡
REV FWD
3 CLEAR
6 +10
9 0
Î
Î
0
4 1 ¡ ¢
7 8 3
A COUSTIC D AMPER MECHANISM
1
Press POWER on the front panel.
1 1
Press STANDBY/ON on the front panel
( on the remote control). (Taiwanese
model)
2
Press SETUP.
When SETUP is pressed for the first time, the
following screen appears. Though the Setup
Navigator may be used more than once, this screen
only appears the first time SETUP is pressed.
Audio1 Audio2 Video
Setup Navigator
Setup Navigator
Setting up using the Setup Navigator
Move
3
Use the cursor buttons (5/∞) to make a
selection.
• If you are going to use the Setup Navigator, it is
not necessary to change the setting on the first
screen. Please proceed to the next step.
• If you do not want to set up the player using
the Setup Navigator, use the cursor button
(∞) to select [Auto Start Off] at this time.
The Setup Navigator function may still be used at
a later time in manual Setup screen menu
operation (page 29).
4
Press ENTER.
The selection is entered and the next Setup
Navigator screen appears.
Use steps 3 and 4 as a basis for entering selections on
the all of the Setup Navigator screens described on the
following pages.
To change the answer to a prior question
Use the cursor button (2) to return to previous
screens. Please note, however, that you cannot go
forward using the cursor button (3), so it will be
necessary to answer all the questions that occur after
the screen that was returned to.
To exit the Setup Navigator
Press SETUP while on any of the screens to exit the
Setup Navigator. Please note that if the Setup Navigator
is exited before all the questions are answered, no
settings are changed.
To return to the Setup screen
Press RETURN. The Setup Navigator is exited and the
Setup screen General menu screen appears. Please
note that no settings are changed if RETURN is pressed
before the Setup Navigator is finished.
Language General
Start
Auto Start Off
ENTER Select SETUP Exit
21